
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X450-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 450mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X450-30-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a 450 mm nominal stroke that can be fine-tuned backward by up to 30 mm, yielding a practical 420-450 mm travel window for exact end-position setting.
This variant includes a carbon steel piston rod and a PT tapered port thread. The extruded aluminum barrel incorporates sensor grooves on both sides, and the -S magnet option enables direct mounting of AirTAC CMSE reed or DMSE electronic solid-state switches for end-of-stroke detection. It supports the reduced SAIJ mounting set: Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X450-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retraction point within the 420-450 mm window during machine setup to accommodate varying product lengths without changing hardware.
Quickly adjust the stroke end-stop on a packaging line when switching between different package sizes, ensuring precise sorting and routing.
Fine-tune the final end position during initial machine commissioning to compensate for mechanical tolerance stack-up without external shims.
The 30 mm rear adjustment screw is ideal for commissioning fine-tuning and product changeovers without swapping cylinders or adding external stops. For holding loads without live air pressure, note that the rear adjuster acts only as a travel stop, not a lock—consider an AirTAC SAIL or BSAI cylinder instead.
Because the 450 mm stroke is relatively long for a 32 mm bore, the 12 mm rod and M10x1.25 thread face higher side-load risks. An external guide rail is recommended to prevent rod binding and premature seal wear. To replace an ISO 15552 cylinder, match the 32 mm bore, 450 mm stroke, 30 mm adjustment, PT G1/8 port, and -S magnet.
Quick checklist
The maximum thrust at 1.0 MPa is 82 kgf.
The rear adjuster screw acts as a mechanical stop that shortens the 450 mm nominal stroke by up to 30 mm, giving a usable travel window of 420-450 mm. It sets the end position but does not lock or hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.