
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X55-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 55mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X55-50-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a 32 mm bore and a 55 mm nominal stroke, but the integrated 50 mm adjusting screw allows you to dial the effective travel back to anywhere within a 5 to 55 mm window. This on-machine tunability is ideal for dialing in precise end positions during commissioning without swapping hardware.
Because this SKU includes the -S magnet option, it supports AirTAC CMSE reed and DMSE electronic sensors directly in the dual-side extruded barrel grooves. The rear adjuster acts purely as a mechanical stop to set the retraction endpoint and relies on the standard variable air cushions for end-of-stroke deceleration. It is important to note that this stopper does not lock or hold the load without continuous live air pressure; for true load-holding, a SAIL or BSAI variant would be required.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X55-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 55 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×55 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adjust the 5-55 mm travel window to accommodate different package sizes on a packaging line without changing out the cylinder.
Fine-tune the retraction end-position during initial machine setup to achieve precise sensor triggering and avoid mechanical hard stops.
Dial in the exact clamping depth for delicate assemblies where a fixed 55 mm stroke would apply too much force or overtravel.
Selecting the SAIJ32X55-50-S makes sense when your machine setup requires variable end-stops or frequent product-size changeovers within a tight 5 to 55 mm travel window. This cylinder uses a PT tapered port thread and a standard carbon steel rod.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 55 mm nominal stroke, 50 mm adjustment range, PT port, and -S magnet. The SAIJ mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2 options, deliberately omitting FB, CA, CB, and CR. Since the stroke is under 300 mm, side-load stress on the 12 mm rod is minimal, though external guides are still recommended for heavy lateral loads.
Quick checklist
At 0.7 MPa, the push force increases to 563 N.
The rear adjusting screw acts as a mechanical stop, allowing you to reduce the 55 mm nominal stroke down to as little as 5 mm. It sets the travel end-point but does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.