
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X550-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 550mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X550-100 is a double-acting ISO 15552 profile cylinder featuring a rear mechanical adjuster that trims the nominal 550 mm stroke back by up to 100 mm, creating a highly flexible 450-550 mm usable travel window.
This model uses a carbon steel piston rod with an M10x1.25 thread and a G1/8 PT tapered port. Unlike fixed-stroke actuators, the rear stopper screw allows you to dial in the exact end-of-stroke position during commissioning without adding external stops. The extruded aluminum barrel includes sensor grooves on both sides, though this non-magnetized variant requires a solid-state DMSE or reed CMSE switch only if a magnet is later retrofitted.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X550-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly dial in the 450-550 mm travel window during product size changes without physically swapping the cylinder or adding external stopper blocks.
Fine-tune the retract position on the fly for multi-format assembly lines that require different end-of-stroke distances per cycle.
Adjust the stroke length to accommodate varying package sizes on a pneumatic diverter arm, ensuring accurate routing without repositioning the entire assembly.
The 100 mm adjustment range is ideal for product changeovers where the end-stop position frequently shifts. If your process demands holding the load at the adjusted position without live air pressure, note that this rear adjuster acts only as a travel stop and not as a lock; you should instead consider an AirTAC SAIL or BSAI locking cylinder.
With a 550 mm stroke, the 12 mm carbon steel rod is highly susceptible to side-loading and sagging. Always pair this actuator with an external guide rail to prevent binding and premature seal wear. For an exact ISO 15552 replacement, match the 32 mm bore, 550 mm stroke, 100 mm adjustment, G1/8 PT port, and the required mounting set (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
If you increase the pressure to 0.7 MPa, the push force rises to 563 N.
The rear adjuster acts as a mechanical stop that allows you to shorten the effective stroke from its nominal 550 mm down to as low as 450 mm. This creates a 100 mm adjustable window for fine-tuning the end position at commissioning, but it does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.