
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X550-100S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 550mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X550-100-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, providing a usable travel window of 450 to 550 mm. This adjustable configuration allows you to dial in the exact retract position without swapping hardware.
Because the nominal 550 mm stroke is relatively long for a 32 mm bore, external guiding is recommended to manage side loads. The extruded aluminum barrel features sensor grooves on both sides, and this -S variant includes a magnet ready for CMSE reed or DMSE electronic solid-state switches. The rear screw acts as a travel stop for end-position tuning, not a load lock.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X550-100S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 450-550 mm retract position during product size changes without physically swapping the cylinder or adding external shims.
Adjust the stroke back by up to 100 mm to accommodate varying package lengths on a sorting line before actuation.
Trim the final end position during setup to perfectly mate with tooling, compensating for mechanical tolerance stack-up.
An adjustable stroke is preferred over a fixed SAI cylinder when commissioning requires fine end-position adjustments or accommodating slight product size variations on a changeover line. The PT port thread and carbon steel rod are standard here.
For any stroke at or above 300 mm, support the load with an external guide to prevent excessive rod bending. If your application requires holding the load in place without continuous live air pressure, note that this cylinder's adjuster is strictly a stop; you would need an external rod lock, a pilot-operated check valve, or an AirTAC SAIL locking cylinder instead. It is dimensionally interchangeable per ISO 15552 and uses the SAIJ mounting subset: Basic, FA, LB, TC, FTC, TCM1, TCM2.
Quick checklist
If you increase pressure to 0.7 MPa, the push force rises to 563 N.
The rear adjuster screw lets you shorten the effective stroke from the 550 mm nominal down to 450 mm. It functions as a travel stop for position tuning and does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.