
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X550-20S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 550mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X550-20-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, allowing you to fine-tune the retract end position by up to 20 mm. This creates a highly usable 530-550 mm travel window, letting you dial in the exact end-of-stroke location during commissioning without adding external stops. It features a carbon steel piston rod and a PT tapered port thread.
The extruded aluminum barrel includes sensor grooves on both sides, and because this SKU includes the -S magnet, it works seamlessly with AirTAC CMSE reed and DMSE solid-state sensors for precise position feedback. The rear adjuster acts solely as a travel stop and does not hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X550-20S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Fine-tune the 530-550 mm retract distance during product line changeovers, setting exact end positions without physically swapping out the cylinder.
Dial in the precise rear stop for delicate operations, adjusting the travel window by up to 20 mm to accommodate varying material thicknesses on the fly.
Leverage the integrated -S magnet with CMSE and DMSE sensors to confirm exact end-stroke positions across the adjustable travel window in automated cells.
Choose this adjustable-stroke variant over a fixed SAI model when your machine setup requires variable end-stops or frequent product-size changeovers that demand a slightly shorter retraction distance. To replace an ISO 15552 cylinder, match the 32 mm bore, 550 mm stroke, PT port, and mounting style. SAIJ supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR.
Because the 550 mm stroke is long relative to the 32 mm bore, the 12 mm rod and M10x1.25 thread will experience greater susceptibility to side loads. An external guide is strongly recommended to prevent rod binding and premature seal wear. For any load-holding requirements without continuous air pressure, this cylinder cannot act as a lock; consider the SAIL or BSAI series instead.
Quick checklist
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective stroke from 550 mm down to as little as 530 mm, providing a 20 mm tuning window for precise end-position calibration without replacing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.