
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X650-20S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 650mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X650-20-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It delivers 402N of pull force at 0.5 MPa and features a 12mm carbon steel rod with an M10x1.25 thread. By turning the rear adjustment screw, you can trim the effective travel back by up to 20mm, creating a precise 630-650mm usable stroke window for fine-tuning end positions at commissioning.
This unit includes a built-in magnet for use with AirTAC CMSE reed and DMSE electronic sensors, which seat neatly into the dual-side sensor grooves on the extruded aluminum barrel. The rear adjuster acts purely as a mechanical stop to set deceleration and travel limits; it is not a lock and cannot hold a load without live air pressure. For applications requiring true load-holding, consider the related SAIL or BSAI series instead.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X650-20S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 630-650mm retract stop during machine commissioning to compensate for mechanical tolerances without machining external stop blocks.
Quickly adjust the stroke end-point by up to 20mm when switching the production line to a slightly different product size or format.
Leverage the integrated magnet with DMSE electronic sensors to confirm the adjusted end-of-stroke position in automated assembly lines.
Choose this 32mm bore when you need 402N pull force at 0.5 MPa and the ability to dial in a 630-650mm travel window without swapping cylinders or adding external stops. If your application requires higher thrust, stepping up to the 40mm bore yields 528N of pull force at the same pressure. Conversely, if your force requirements are lower, dropping to a smaller bore is more efficient. The integrated magnet (-S) enables direct position feedback via CMSE or DMSE switches.
Because the 650mm stroke is long relative to the 32mm bore, the 12mm rod is susceptible to side-loading and bending under offset loads; an external guide rail is recommended to prevent premature seal wear. This cylinder uses a PT tapered port and supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2. It is dimensionally interchangeable per ISO 15552, making it a direct replacement for standard ISO profile cylinders without claiming brand equivalence.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 82kgf.
A rear mechanical screw acts as an external stopper, allowing you to shorten the 650mm nominal stroke by up to 20mm, resulting in a usable travel window of 630-650mm. This adjuster only sets the travel end and does not lock or hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.