
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X650-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 650mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X650-50-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a nominal 650 mm stroke that can be fine-tuned backward by up to 50 mm, creating a precise 600-650 mm usable travel window.
Because the adjuster acts purely as a mechanical stop for end-position tuning, it does not lock the load without live air pressure. The extruded aluminum barrel includes sensor grooves on both sides, and the integrated -S magnet enables position detection using AirTAC CMSE reed or DMSE electronic solid-state switches.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X650-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retraction point within the 600-650 mm window during machine commissioning to accommodate different material lengths without external stopper hardware.
Quickly adjust the stroke by up to 50 mm on packaging lines when switching between product formats, minimizing downtime and avoiding cylinder replacement.
Utilize the 650 mm travel for reaching deep into machine cavities, relying on the fine adjustment to set the precise final pressing position.
If your setup needs less force, stepping down is not an option below 32 mm in this series, but stepping up to a 40 mm bore yields 628 N. The adjustable stroke is specified here to allow commissioning fine-tunes and product-size changeovers without swapping the cylinder or adding external stops. To replace an ISO 15552 cylinder, match the 650 mm stroke, 50 mm adjustment range, PT tapered port threads, and the -S magnet requirement.
At 650 mm of travel, the 12 mm rod is highly susceptible to side-loading forces. Even with adjustable air cushions at both ends, you must use an external guide to prevent rod binding and premature seal wear. Remember that the rear adjuster only sets the travel end; for load-holding without live pressure, select an external rod lock or a SAIL pneumatic lock cylinder. Mounting options are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
At a maximum 1.0 MPa pressure, it achieves 82 kgf.
The rear adjusting screw acts as a mechanical stopper that shortens the effective stroke. For this 650 mm nominal stroke model, you can trim the travel back by up to 50 mm, yielding a usable 600-650 mm positioning window. It requires live air to maintain position and does not lock the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.