
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X75-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 75mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X75-75 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to trim the nominal 75 mm travel back by up to 75 mm, yielding a highly versatile 0-75 mm usable window.
Equipped with a G1/8 port and a 12 mm carbon steel rod, this unit includes variable air cushions at both ends to manage deceleration. The extruded aluminum barrel provides sensor grooves on both sides, ready to accept AirTAC CMSE reed or DMSE electronic switches if a magnet is added later.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X75-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 0-75 mm stroke required for new product sizes on a packaging line without replacing the cylinder or adding mechanical shims.
Fine-tune the retract end position during commissioning to ensure precise alignment of pick-and-place actuators.
Use the rear stopper to easily adjust the travel limit for testing different clamping depths on small assembly fixtures.
Choose this 32 mm bore when your application requires precise end-position tuning during commissioning or frequent product changeovers, as the rear screw allows variable end-stops without swapping cylinders or adding external stops. If your setup needs more thrust, stepping up to the 40 mm bore increases push force to 628 N at 0.5 MPa. Because the stroke is under 300 mm, side-load risks are moderate, but always guide the load externally for optimal rod life.
When specifying a replacement, verify the 75 mm nominal stroke, 75 mm adjustment range, PT tapered port threads, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the rear adjuster acts only as a travel stop and does not hold the load without live air; for dead-load holding, consider an external rod lock or the SAIL series.
Quick checklist
At the maximum 1.0 MPa pressure, it achieves 82 kgf.
The rear adjuster screw allows you to shorten the effective stroke by up to 75 mm from the 75 mm nominal length, creating a 0-75 mm adjustable travel window. The adjuster functions as a mechanical stop and does not lock the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.