
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X800-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 800mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X800-100 is a double-acting, double-rod ISO 15552 profile cylinder engineered for precise retract-end tuning. It features a 32 mm bore, an 800 mm nominal stroke, and a rear mechanical adjuster that allows you to shorten the effective travel by up to 100 mm, creating a usable 700-800 mm stroke window without swapping hardware.
This extruded aluminum barrel design includes dual sensor grooves for CMSE reed and DMSE electronic switches, though this specific SKU omits the magnet. The PT tapered port is G1/8, and the 12 mm carbon steel rod with an M10x1.25 thread handles standard loads. Because the stroke reaches 800 mm, an external guide is strongly recommended to counter side-load deflection on the extended rod.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X800-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 700-800 mm travel window during product size changes to set new retract positions without machining new stopper blocks.
Actuate diverter arms on extended conveying lines where the exact end position must be fine-tuned to match varying pallet depths.
Trim the retract stroke by up to 100 mm during setup to perfectly time the machine cycle and prevent mechanical collisions.
Select this 32 mm bore actuator when an application requires exact end-position calibration during commissioning or product changeover, replacing the need for fixed external stops. For load-holding without continuous air pressure, note that the rear adjuster acts only as a travel stop and not a brake; an external rod lock or an AirTAC SAIL cylinder is required.
To match this ISO 15552 interchangeable cylinder, confirm your bore (32 mm), stroke (800 mm), adjustment range (-100 mm), port type (PT), and mounting choice. SAIJ supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR styles found on some standard actuators.
Quick checklist
The rear adjuster acts as a mechanical stop that shortens the retract stroke by up to 100 mm. This yields an effective travel window of 700-800 mm, allowing you to fine-tune the end position without modifying the cylinder mounting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.