
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X85-20 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 85mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X85-20 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. By turning the external stopper screw, you can shorten the effective travel, providing a usable stroke window of 65 to 85 mm for precise end-position tuning during commissioning.
It features variable air cushions at both ends and extruded aluminum barrel sensor grooves on two sides, accepting reed CMSE or solid-state DMSE switches if a magnet is added later.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X85-20 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 85 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×85 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end-stop during initial commissioning, trimming up to 20 mm off the nominal 85 mm stroke to perfect the resting position without external shims.
Quickly adapt the cylinder travel window from 65 to 85 mm when switching the production line to a slightly different product size or thickness.
Use the rear adjuster to set a precise retract distance for delicate pick-and-place operations where a hard fixed stroke might crash the tooling.
Choose this adjustable model over a fixed-stroke SAI when you need to fine-tune the retract end-position on the fly without swapping cylinders or adding external stops. If your application requires slightly less push force, stepping down to a 25 mm bore (if available) or a smaller frame makes sense, while stepping up to a 40 mm bore yields 528 N of pull at 0.5 MPa for heavier loads.
For ISO 15552 replacement matching, specify a 32 mm bore, 85 mm stroke, 20 mm adjustment, PT tapered port thread, and no magnet. Because the stroke is under 300 mm, side-load stress is manageable, but long unsupported loads still need an external guide. Note that the rear adjuster acts only as a travel stop; it does not hold the load without live air, so for true load-holding you need an SAIL or BSAI cylinder.
Quick checklist
At the maximum operating pressure of 1.0 MPa, it can deliver up to 82 kgf.
The rear external stopper screw lets you mechanically shorten the stroke by up to 20 mm. This creates an adjustable travel window from 65 to 85 mm, allowing you to set the exact retract end-position without changing the cylinder itself.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.