
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X850-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 850mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X850-10 is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, allowing you to dial back the nominal 850 mm travel by up to 10 mm. This yields a usable 840-850 mm end-position window for fine-tuning at commissioning without swapping hardware.
Because the 850 mm stroke approaches the 1000 mm maximum for this bore, the 12 mm carbon steel rod and M10x1.25 thread face substantial leverage on extension, so an external guide is strongly advised to prevent side-load wear. The extruded aluminum barrel carries sensor grooves on both sides, and while this specific SKU lacks a magnet, adding a -S variant enables CMSE reed and DMSE solid-state switch integration.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X850-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 850 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×850 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 840-850 mm retract stop during product size changes on a long-stroke handling line without adding external spacers.
Fine-tune the end position of a 32 mm bore diverting mechanism operating over an 850 mm span to compensate for belt stretch.
Adjust the 10 mm travel window during commissioning to set exact pressing or locating depths on an automated assembly fixture.
If your setup needs more thrust, stepping up to the 40 mm bore yields 628 N. The 10 mm rear adjuster acts purely as a mechanical stop to set the exact retract position, and combined with the variable air cushion at both ends, it decelerates the load. It does not hold the load without live air pressure; for fail-safe load holding, consider the SAIL or BSAI series.
This cylinder is dimensionally interchangeable per ISO 15552 mounting interfaces and uses a PT tapered port thread. It supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR brackets. Given the 850 mm stroke, always pair it with an external linear guide to manage rod side-load.
Quick checklist
At 0.7 MPa, the push force increases to 563 N.
The rear adjuster screw lets you shorten the effective travel from the nominal 850 mm down to 840 mm, giving a 10 mm fine-tuning window. It functions as a mechanical stop and does not lock the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.