
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X850-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 850mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X850-75-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a 775 to 850 mm usable travel window, allowing you to dial back the nominal 850 mm stroke by up to 75 mm during commissioning.
This unit includes a standard magnet for CMSE reed and DMSE electronic sensors, which seat neatly into the extruded aluminum barrel's dual sensor grooves. Because the stroke exceeds standard ranges, it is built to order; the 12 mm carbon steel rod and M10x1.25 thread handle basic loads, but an external guide is recommended over this long travel to prevent rod side-loading.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X850-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 850 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×850 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 775 to 850 mm end-position during product size changes without replacing the cylinder or adding external mechanical stops.
Fine-tune the retract stop on long-stroke assembly lines to accommodate varying part lengths and ensure precise component placement.
Use the 75 mm rear adjustment window to perfect the deceleration point and avoid hard impacts at the end of the 850 mm travel cycle.
Choose this adjustable-stroke model over a fixed SAI when your machine setup requires variable end-stops or fine-tuning without physically swapping the cylinder or adding external stops. If your application needs less force, stepping down is not an option in this series, but stepping up to a 40 mm bore yields 628 N at 0.5 MPa. The SAIJ32X850-75-S uses a PT tapered G1/8 port and supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts.
Remember that the rear adjuster acts purely as a travel stop to set deceleration endpoints; it does not hold the load without live air. For true fail-safe load holding, consider the SAIL or BSAI series. At 850 mm of travel, always use an external guide rail to support the load and protect the rod.
Quick checklist
At 0.7 MPa, the push force increases to 563 N.
The rear adjuster allows you to shorten the effective travel from the nominal 850 mm down to 775 mm. It acts as a physical stop to fine-tune the end position, but it is not a lock and will not hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.