
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X90-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 90mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X90-50-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. With a nominal 90 mm stroke and a 50 mm adjustment range, it provides a wide usable travel window of 40 to 90 mm, allowing you to dial in the exact retract end-position during commissioning.
This 32 mm bore unit uses a PT tapered G1/8 port and a 12 mm carbon steel rod with an M10x1.25 thread. Because the rear adjuster acts strictly as a mechanical stop and the standard air cushions manage deceleration, neither will hold a load without live air pressure. For load-holding requirements, consider an external rod lock or the related SAIL series. The extruded aluminum barrel includes sensor grooves on both sides, compatible with AirTAC CMSE reed and DMSE electronic sensors.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X90-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract stop from 40 to 90 mm during format changes on a packaging line, eliminating the need to physically swap out the cylinder for different carton sizes.
Fine-tune the end-of-stroke position during machine setup to perfectly time the pick-and-place sequence without adding bulky external stopper blocks to the frame.
Set the precise travel distance for a testing fixture, using the 50 mm adjustment window to accommodate varying part lengths on the fly.
Choose this adjustable-stroke model when your machine setup requires frequent product changeovers or fine-tuning of the retract position without swapping cylinders or adding external stops. The SAIJ mounting set is limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options found on some fixed-stroke lines.
When ordering a replacement, match the 32 mm bore, 90 mm nominal stroke, 50 mm adjustment, PT G1/8 port, and the -S magnet requirement. The 12 mm rod with an M10x1.25 thread handles moderate side loads, but for long unsupported strokes at or above 300 mm, an external guide is recommended to prevent rod binding.
Quick checklist
The rear adjuster screw lets you mechanically shorten the effective stroke by up to 50 mm. This turns the 90 mm nominal stroke into a usable travel window of 40 to 90 mm, which can be fine-tuned at commissioning without replacing the cylinder.
If you increase the pressure to 0.7 MPa, the push force rises to 563N.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.