
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X95-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 95mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X95-50-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a usable travel window of 45 to 95 mm, allowing you to dial back the 95 mm nominal stroke by up to 50 mm during commissioning.
Because this is an adjustable-stop variant rather than a fixed-stroke SAI, you can fine-tune the retract end-position without swapping the barrel or adding external stops. The extruded aluminum profile includes sensor grooves on both sides, and the integrated -S magnet works seamlessly with AirTAC CMSE reed and DMSE electronic switches for position feedback.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X95-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract position within the 45-95 mm window when switching product formats on a packaging line, avoiding physical cylinder swaps.
Fine-tune the end-of-stroke position during commissioning to perfect a pressing or clamping distance without machining external stopper blocks.
Leverage the built-in magnet for CMSE or DMSE sensors alongside the rear adjuster to confirm the exact trimmed stroke position in automated assemblies.
If you need less force, there is no smaller ISO 15552 bore in this range; if you need significantly more thrust, stepping up to the 40 mm bore yields 628 N at 0.5 MPa. The rear adjuster is strictly a travel stop, not a locking device, so it will not hold a load without live air pressure. For fail-safe load holding, consider the SAIL or BSAI series instead.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 95 mm nominal stroke, PT tapered port, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). The 12 mm rod diameter handles moderate side loads, but for any stroke over 300 mm, an external guide is recommended to prevent rod wear.
Quick checklist
At the maximum operating pressure of 1.0 MPa, it delivers up to 801 kgf.
The rear adjusting screw acts as a mechanical stopper that lets you shorten the effective stroke from its 95 mm nominal length down to as little as 45 mm. This provides a 45-95 mm adjustable travel window for fine-tuning the retract end-position without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.