Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S
The AirTAC B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S is a genuine double-acting standard air cylinder with a Ø32mm bore and 50mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ32 mm
- Stroke50 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 21 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S
The B06-SC32X50S is a battery-manufacturing dedicated variant of the standard AirTAC SC32X50S double-acting tie-rod cylinder. The B06- prefix designates its application in battery assembly lines, though its physical specifications remain completely identical to the base model. It features a 32mm bore and a 50mm stroke, driven by filtered air at 0.15 to 1.0 MPa.
This compact actuator provides a push force of 402 N at 0.5 MPa and 724 N at the maximum 0.9 MPa operating pressure. The S suffix indicates a built-in piston magnet, allowing CMSG or DMSG sensors to track position along the 140 mm body. Adjustable end cushions span 21 mm to soften impact at stroke ends.
Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S Technical Specifications
| Model | Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S Is Used
Cell Stacking Presses
Applies controlled 563 N clamping force at 0.7 MPa for aligning and stacking battery cells during module assembly.
Tab Welding Feed
Uses the 50mm stroke to position battery tabs accurately under welding heads, with sensor feedback via the magnetic piston.
Pack Handling Stops
Acts as a compact pneumatic stopper on conveyor lines routing battery packs, benefiting from the 140mm body length.
Is the Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S the Right Cylinder?
Choose this 32mm bore when your battery handling system requires moderate force up to 724 N at 0.9 MPa. If your tabbing or stacking process needs less force, stepping down is not an option below 32mm in this family, but stepping up to a 40mm bore yields 628 N at just 0.5 MPa. The built-in magnet allows precise end-of-stroke detection for tightly sequenced cell assembly.
When replacing this unit, match the 32mm bore, 50mm stroke, PT1/8 port thread, and the built-in magnet. Although the 50mm stroke is short and highly resistant to rod bending, always ensure axial load alignment to maximize seal and bearing life.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S FAQ
The B06- prefix indicates this cylinder is part of AirTAC's battery-manufacturing dedicated line. Mechanically and dimensionally, it is identical to the standard SC32X50S, featuring the same 32mm bore, 50mm stroke, and 724N maximum thrust at 0.9 MPa.
No, this is a double-acting pneumatic cylinder and does not lock or hold position without live air pressure. The adjustable cushion only decelerates the piston at stroke ends. To hold a load mechanically during pressure loss, an external rod brake or pilot-operated check valve is required.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B06-SC Battery-Dedicated Standard Cylinder B06-SC32X50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.