Airtac SAID32 Double Rod Cylinder SAID32AX185S
The AirTAC SAID32 Double Rod Cylinder SAID32AX185S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 185mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke185 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAID32 Double Rod Cylinder SAID32AX185S
The AirTAC SAID32X185-S is a double-acting, double-rod ISO 15552 profile cylinder. Because a rod extends from both end covers, the annulus area is identical on the extend and retract sides. This means the push and pull forces are perfectly equal, providing 345 N of force each way at 0.5 MPa. The 185 mm stroke is a non-standard made-to-order length, extending past the typical standard increments.
This variant features a SUS420J2 stainless steel rod for superior corrosion resistance and includes a built-in magnet (-S) for position sensing. The extruded aluminum barrel includes sensor grooves on both sides, supporting AirTAC CMSE reed and DMSE electronic solid-state switches. The piston rod exits both ends, allowing you to mount the primary workpiece on one side and a cam or position flag on the rear rod for dual-side guidance.
Airtac SAID32 Double Rod Cylinder SAID32AX185S Technical Specifications
| Model | Airtac SAID32 Double Rod Cylinder SAID32AX185S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 185 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAID32 Double Rod Cylinder SAID32AX185S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×185 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAID32 Double Rod Cylinder SAID32AX185S Is Used
Symmetric Force Transfer
Ideal for shuttle mechanisms requiring identical 345 N push and pull forces at 0.5 MPa, ensuring perfectly balanced motion without speed variations.
Dual-Side Tooling Actuation
The through-rod design allows mounting a primary workpiece on the front rod and a secondary cam or limit flag on the rear rod for synchronized machine timing.
Anti-Rotation Guiding
Twin rod ends provide superior resistance to torsional twisting on sliding loads compared to single-rod cylinders, maintaining precise linear tracking.
Is the Airtac SAID32 Double Rod Cylinder SAID32AX185S the Right Cylinder?
Choose this 32 mm bore double-rod cylinder when an application demands equal force and speed in both directions, or when rear-rod anti-rotation guidance is required. If you need higher thrust, stepping up to the 40 mm bore yields 528 N each way at 0.5 MPa. Unlike a single-rod SAI, this SAID model uses a reduced mounting accessory set: Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). It is dimensionally interchangeable per ISO 15552.
The PT tapered port thread is G1/8. Note that a plain SAID cylinder does not hold its load when air pressure is lost or exhausted; the piston will drift. Use a SAIL (air-released lock) or BSAID (clamp-lock) if position holding is required. Since the 185 mm stroke is non-standard, confirm overall rear-rod clearance in your design.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAID32 Double Rod Cylinder SAID32AX185S FAQ
Because it is a double-rod cylinder, the effective area is the same on both sides. It delivers an equal 345 N of force in both extend and retract directions at 0.5 MPa (483 N at 0.7 MPa, 621 N at 0.9 MPa).
Yes, the SAID32X185-S is dimensionally interchangeable with other ISO 15552 profile cylinders. It uses the standard ISO mounting interface but features a double-rod configuration that requires additional rear clearance.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAID32 Double Rod Cylinder SAID32AX185S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.