
The AirTAC SAID32 Double Rod Cylinder SAID32BX175 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 175mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X175 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 175mm stroke. Because a rod exits both ends, the annulus area is identical on extend and retract, yielding exactly 483N of force in each direction at 0.7 MPa. This symmetric output is ideal for mechanisms requiring consistent push and pull dynamics.
This configuration uses SUS304 stainless steel rods (material code B) for superior corrosion resistance in wet or mildly chemical environments. The extruded aluminum barrel includes sensor grooves on both sides. Although no magnet is specified here, adding one enables AirTAC CMSE reed or DMSE electronic switches for dual-end position detection.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX175 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage with equal 483N push and pull force at 0.7 MPa, ensuring consistent acceleration and deceleration without speed disparities.
The twin 12mm SUS304 rods guide the payload securely, preventing torsional twist on precision linear slides where a single rod would allow minor rotation.
Mounts the primary tool on the front rod end and a secondary cam or mechanical flag on the rear protruding rod to trigger external limit switches.
Select this 32mm bore when an application demands exactly 483N both ways at 0.7 MPa, or step up to the 40mm bore (528N) if your symmetric load requires slightly more push and pull force. The double-rod design inherently resists rotation better than a single-rod SAI, allowing you to mount a workpiece on the front rod and a cam or position flag on the rear rod. Note that a plain SAID does not hold position if air pressure is lost; for dead-load holding, consider an external pilot-operated check valve or the BSAID clamp-lock variant.
As a dimensionally interchangeable ISO 15552 cylinder, it drops in seamlessly with other standard profile bodies. It accepts PT tapered port threads (G1/8) and supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). With a 175mm stroke, the 12mm rod handles moderate loads, but always verify side-load limits on the rod bearing.
Quick checklist
Because it is a double-rod cylinder, the effective piston area is the same on both sides. It delivers 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa in both the extend and retract directions.
Yes, the SAID32X175 is dimensionally interchangeable per ISO 15552 profile standards. It shares standard mounting dimensions and uses a G1/8 port, making it a direct replacement for other ISO 15552 double-rod cylinders, though it uses a reduced mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.