
The AirTAC SAID32 Double Rod Cylinder SAID32BX190S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 190mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X190-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 190mm stroke. Because the piston rod extends from both end covers, the annulus area is identical on both sides, yielding exactly 483N of force in both extend and retract directions at 0.5 MPa. The -S suffix denotes an integrated magnet for position sensing.
This variant is configured with SUS304 stainless steel rods (code B) for superior corrosion resistance and includes PT tapered port threads. The extruded aluminum barrel integrates sensor grooves on both sides, allowing you to mount CMSE reed or DMSE electronic switches along either side of the body to track the piston.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX190S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 190 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×190 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a push-pull transfer arm where the 345N output at 0.5 MPa must be identical in both directions to maintain consistent cycle timing without pressure spikes.
Powers a vertical lifting slide using the twin rods to resist torsional twisting, keeping the payload perfectly aligned without external linear bearings.
Actuates a primary workpiece on the front rod while the protruding rear rod mechanically triggers a secondary limit valve or physical cam mechanism.
Select this 32mm bore when an application requires symmetric force and speeds up to 30-800 mm/s. If you need higher thrust, stepping up to the 40mm bore raises the bidirectional force to 528N at 0.5 MPa. The twin-rod architecture is chosen over a single-rod SAI when the mechanism requires dual-side guidance to prevent rotation, or when a rear rod end is needed to mount a cam or position flag. Note that the SAID mounting accessory set is limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR brackets found on single-rod variants.
Because the stroke is 190mm, the unsupported rod length is moderate, but for optimal bearing life, external guidance is recommended if heavy off-center loads are present. This cylinder is dimensionally interchangeable per ISO 15552, uses a G1/8 port, and relies on adjustable air cushions at both ends to decelerate the piston. It will drift if air pressure is lost, so a SAIL or BSAID lock variant is required for fail-safe holding.
Quick checklist
Because it is a double-rod cylinder, the force is equal in both directions. It provides 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa for both extension and retraction.
Yes, the SAID32X190-S is dimensionally interchangeable per ISO 15552 and serves as a direct replacement for other ISO 15552 double-rod profile cylinders, utilizing a G1/8 port and standard mounting dimensions.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.