
The AirTAC SAID32 Double Rod Cylinder SAID32BX270 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 270mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X270 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 270mm stroke. Because the piston rod extends from both end covers, the effective annulus area is identical on the extend and retract sides. This provides an equal force of 483N and consistent speed in both directions at 0.7 MPa.
This configuration uses SUS304 stainless steel rods (code B) for superior corrosion resistance, making it suitable for humid or mildly corrosive environments. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE reed or DMSE electronic switches. You can mount the primary workpiece on the front rod and a cam or position flag on the rear rod to trigger external sensors.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX270 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 270 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×270 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer shuttle where the 483N force must remain identical whether pushing a part forward or pulling it back, ensuring consistent cycle timing.
Powers a vertical lifting slide where the twin SUS304 rods prevent the platform from twisting under offset loads, maintaining strict guiding accuracy.
Actuates a clamping mechanism on the front rod while the rear rod protrudes to drive a physical cam, triggering a solid-state DMSE sensor externally.
Choose this 32mm bore when an application requires 483N of thrust and retraction force simultaneously. If your project demands less force, stepping down is not an option in the SAID series as 32mm is the smallest bore. If you need significantly more push or pull, consider the 40mm bore, which provides 739N at 0.7 MPa. The double-rod design is preferred over a single-rod SAI when you need dual-side guidance, anti-rotation stability, or a rear-rod extension for secondary mechanisms.
This cylinder uses PT tapered port threads and a G1/8 air supply port. It supports the reduced SAID mounting accessory set: Basic, FA, LB, TC, FTC, TCM1, and TCM2. Note that FB, CA, CB, and CR mounts are reserved for single-rod SAI cylinders. Since this is a standard 270mm stroke, it falls within the 1000mm maximum for this bore. Because the stroke is under 300mm, side-load stress on the rod bearing is moderate, but an external guide is still recommended for heavy lateral loads. Remember that the adjustable air cushions only decelerate the piston near the end caps; they do not hold a load. If air pressure is lost, the cylinder will drift. For position holding, use an external rod lock or explore the SAIL or BSAID series.
Quick checklist
Because it is a double-rod cylinder, the rod area is subtracted from both sides of the piston. This means the extend and retract forces are equal. At 0.7 MPa, it provides 483N of force in both directions.
Yes, it is dimensionally interchangeable per ISO 15552. However, the SAID series uses a specific mounting subset: Basic, FA, LB, TC, FTC, TCM1, and TCM2. It does not support FB, CA, CB, or CR mounts due to the rear rod protrusion.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.