
The AirTAC SAID32 Double Rod Cylinder SAID32BX280S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 280mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X280-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 280mm stroke. Because the piston rod exits both end covers, the annulus area is identical on both sides, yielding equal push and pull forces. This specific bore generates 483 N of thrust and retraction force at 0.7 MPa, ensuring perfectly symmetric motion dynamics.
Equipped with a magnet for position sensing, this variant uses SUS304 stainless steel rods for superior corrosion resistance. The rear rod extension is ideal for mounting a cam or position flag, while the extruded aluminum barrel integrates sensor grooves on both sides for flexible CMSE or DMSE switch mounting.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX280S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage where the 345 N bidirectional force at 0.5 MPa pushes and pulls a workpiece with identical speed and energy on both strokes.
The twin SUS304 rods keep the load guided and prevent rotational drift during vertical lifting operations over the 280mm travel.
Operates a primary clamping tool on the front rod while the rear protrusion directly triggers a DMSE solid-state sensor flag at mid-stroke.
Select this double-rod cylinder when an application demands equal force and speed in both directions, or requires anti-rotation guidance and rear-rod sensing that a standard single-rod SAI cannot provide. If your project needs less force, stepping down is not an option below 32mm, but stepping up to a 40mm bore yields 528 N at 0.5 MPa. For this 280mm stroke, the unsupported length is significant; you must use an external guide to prevent rod-bearing bending under side loads.
As a dimensionally interchangeable ISO 15552 profile cylinder, it serves as a direct replacement for other standard double-rod units. It uses a PT G1/8 port and supports mounting accessories Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). Note that the adjustable air cushions only decelerate the piston near stroke end; this cylinder will drift and cannot hold a load without live air pressure. For locking needs, consider SAIL or BSAID variants.
Quick checklist
Because it is a double-rod cylinder, the push and pull forces are equal. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa in both directions.
Yes, it is dimensionally interchangeable per ISO 15552. You can use it as a direct replacement for other ISO 15552 profile cylinders, utilizing standard mounting accessories like FA, LB, and TC.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.