
The AirTAC SAID32 Double Rod Cylinder SAID32BX375 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 375mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X375 is a double-acting, double-rod ISO 15552 profile cylinder engineered for symmetric actuation. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on extend and retract, yielding an equal 483 N of force in both directions at 0.7 MPa.
This through-rod architecture allows you to mount the primary workpiece on the front end and a position flag or cam on the rear. The extruded aluminum barrel features sensor grooves on both sides, though position detection requires adding a magnet (-S) to enable CMSE reed or DMSE electronic switches.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX375 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 375 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×375 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage where the matching extend and retract speed prevents jerky movements, ensuring smooth part handoff between stations.
Powers a vertical lifting slide where the twin-rod geometry resists torsional twist, keeping the tooling plate perfectly level during travel.
Actuates a clamping mechanism on the front stroke while using the rear rod protrusion to trigger a physical limit cam for secondary validation.
Choose this 32 mm bore when an application demands 483 N of thrust and pull simultaneously, stepping up from a smaller bore if guiding fails, or down to a 40 mm bore (739 N) if the load stalls. A twin-rod design is preferred over a single-rod SAI when you need dual-side guidance to prevent rotation or require rear-end sensing. Note that the adjustable air cushions only decelerate the piston near stroke end; they do not hold the load if air pressure drops. For position holding without live pressure, consider an external rod lock or a SAIL cylinder.
At 375 mm of stroke, the 12 mm rod is highly susceptible to side-load bending and rod-bearing wear. Always support the load with an external linear guide to prevent premature seal failure. This cylinder is dimensionally interchangeable per ISO 15552 and uses PT tapered ports, accepting mounting accessories from the Basic, FA, LB, TC, FTC, TCM1, and TCM2 set only.
Quick checklist
Because it is a double-rod cylinder, the push and pull forces are equal. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa in both directions.
Yes, it is dimensionally interchangeable with ISO 15552 profile cylinders. It supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, but omits FB, CA, CB, and CR brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.