
The AirTAC SAID32 Double Rod Cylinder SAID32BX400S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 400mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X400-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 400mm stroke. Because the piston rod extends from both end covers, the effective annulus area is identical on both sides, yielding exactly 345 N of force in both extend and retract directions at 0.5 MPa. This through-rod geometry provides superior anti-rotation guidance and allows a secondary mechanism or position flag to be driven from the rear rod end.
This specific configuration includes a piston magnet for use with AirTAC CMSE reed and DMSE electronic sensors, which ride in the dual-side sensor grooves machined into the extruded aluminum barrel. It is equipped with SUS304 stainless steel rods for enhanced corrosion resistance and features PT tapered port threads.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX400S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage where the equal 345 N extend and retract forces ensure consistent acceleration and deceleration without requiring pressure adjustments between strokes.
The twin-rod architecture prevents the 400mm stroke payload from twisting under offset loads, maintaining strict parallelism for precision sliding fixtures.
Mounts the primary tool on the front rod end while using the rear rod protrusion to trip a DMSE solid-state sensor, providing a mechanical confirmation signal.
Select this double-rod cylinder when an application demands equal push and pull forces (345 N each way at 0.5 MPa) or requires dual-side guidance to prevent load rotation. If you need higher thrust, stepping up to the 40mm bore neighbor increases both-way force to 528 N. Unlike a single-rod SAI, this SAID model mounts the workpiece on one end and can drive a rear cam or sensor target. Note that a plain SAID does not hold position unpowered; use a SAIL lock cylinder or external pilot check valve if load holding is required.
At 400mm of stroke, the 12mm rod and M10x1.25 thread face increased bending moments under side loads, so an external guide rail is recommended for the payload. For ISO 15552 direct replacements, match the 32mm bore, 400mm stroke, PT ports, and the required mounting accessory. SAID supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, omitting FB, CA, CB, and CR. The variable air cushions at both ends decelerate the piston near stroke end but do not function as a brake.
Quick checklist
Because the rod occupies both sides of the piston, the effective area is equal in both directions. It provides 345 N of force at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa for both extension and retraction.
Yes, the SAID32X400-S is dimensionally interchangeable per ISO 15552. It shares the standard 32mm bore footprint, PT porting, and standard mounting accessories, allowing it to serve as a direct replacement for other ISO 15552 profile cylinders.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.