
The AirTAC SAID32 Double Rod Cylinder SAID32BX40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 40mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X40-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 40mm stroke. Because the piston rod extends from both end covers, the annulus area is identical on both sides, yielding exactly 345N of force in both extend and retract directions at 0.5 MPa. This symmetric output is ideal for mechanisms requiring perfectly balanced push and pull dynamics.
Equipped with a magnetic piston (-S), it supports AirTAC CMSE reed and DMSE electronic solid-state sensors housed within the dual-side extruded barrel grooves. The twin rods are crafted from SUS304 stainless steel (code B) for superior corrosion resistance, and fluid connections use PT tapered threads. The rear rod end can simultaneously drive a secondary load or mount a position flag, while the front handles the primary workpiece.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer shuttle where the 345N extend and retract forces must be identical to maintain consistent acceleration on both strokes without tweaking regulator pressures.
Powers a vertical lifting slide using the twin SUS304 rods to guide the load and prevent torsional twisting that a single rod cannot suppress.
Actuates a small clamping fixture on the front stroke while the rear rod end trips a DMSE solid-state sensor flag to confirm full retraction to the controller.
Select this 32mm bore when an application demands equal 345N bi-directional force at 0.5 MPa, stepping down from a 40mm bore (528N) to save space, as a single-rod SAI would create unequal push/pull forces. A double-rod design is chosen over single-rod variants when you need dual-side guidance to prevent rotation, or require rear-rod sensing via CMSE/DMSE switches. The reduced SAID mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR brackets found on single-rod SAI units.
It is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other standard profile double-rod cylinders. Note that a plain SAID does not hold position or carry loads if air pressure is lost; for dead-load holding, consider an external pilot-operated check valve or the BSAID clamp-lock variant. The overall length is slightly longer than a single-rod cylinder to accommodate the rear rod protrusion, so verify your clearance.
Quick checklist
Because it is a double-rod cylinder, the force is equal in both directions. It generates 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa for both extend and retract strokes.
Yes, it is a profile cylinder dimensionally interchangeable per ISO 15552. You can drop it in for other standard ISO 15552 double-rod cylinders, matching the 32mm bore, 40mm stroke, and PT port interface.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.