
The AirTAC SAID32 Double Rod Cylinder SAID32BX425S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 425mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X425-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 425mm stroke. Because the piston rod exits both end covers, the effective annulus area is identical in both directions, yielding perfectly symmetric thrust of 483N at 0.5MPa and 621N at 0.9MPa for extend and retract alike.
This specific configuration incorporates SUS304 stainless steel rods (material code B) for superior corrosion resistance and includes a built-in magnet for position sensing. The extruded aluminum barrel features sensor grooves on both sides, allowing you to mount CMSE reed or DMSE electronic switches on either end to track the through-rod motion.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX425S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage where the 483N force at 0.7MPa must remain identical whether pushing a part forward or pulling it back to home.
Twin 12mm SUS304 rods keep the workpiece guided and prevent rotation during vertical lifting tasks over the 425mm travel.
Operates a primary tool on the front rod while the rear protrusion triggers a DMSE electronic sensor for a secondary confirmation signal.
Select this 32mm bore unit when an application demands equal push and pull forces, such as 345N at 0.5MPa both ways, alongside dual-side anti-rotation guidance. If your mechanism requires higher thrust, stepping up to the 40mm bore increases the bidirectional force to 528N at 0.5MPa. Conversely, if you need less force and a shorter footprint, a smaller bore would suffice. This SAID variant uses a PT tapered port thread and omits the FB, CA, CB, and CR mounts, utilizing only the Basic, FA, LB, TC, FTC, TCM1, and TCM2 ISO 15552 mounting set.
With a 425mm stroke, the 12mm diameter rod and its M10x1.25 thread face potential bending moments under heavy lateral loads; an external guide rail is recommended to prevent rod-bearing wear. Note that while the adjustable air cushions at both ends decelerate the piston near stroke end, this cylinder will drift if air pressure is lost—use a SAIL lock or external pilot check valve if position holding is required.
Quick checklist
Because it is a double-rod cylinder, the push and pull forces are equal. It generates 345N at 0.5MPa, 483N at 0.7MPa, and 621N at 0.9MPa in both directions.
Yes, it is dimensionally interchangeable per ISO 15552. It serves as a direct replacement for other ISO 15552 double-rod profile cylinders, matching standard mounting dimensions while offering PT ports and SUS304 rods.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.