
The AirTAC SAID32 Double Rod Cylinder SAID32BX450S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 450mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X450-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 450mm stroke. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on each side. This means extend and retract forces are perfectly equal, delivering 483 N of thrust in both directions at 0.7 MPa.
The -S suffix indicates an integrated magnet for position sensing via AirTAC CMSE reed or DMSE electronic switches fitted into the dual side sensor grooves. A second rod end allows you to mount a cam or limit flag on the rear for dual-side guidance, while the PT tapered port threads ensure a tight pneumatic seal.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX450S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a workpiece from one end while the matching rear rod end simultaneously pushes a secondary mechanism, utilizing the exact 483 N thrust in both directions.
Twin SUS304 rods exiting both covers keep the payload guided and prevent rotational drift over the 450mm travel distance.
The integrated -S magnet pairs with CMSE and DMSE switches, allowing you to track a rear-mounted cam flag for precise stroke confirmation.
Choose this double-rod configuration when an application demands equal 483 N force both ways and superior anti-rotation resistance compared to a single-rod SAI. If you need less thrust, dropping to a smaller bore is an option, but stepping up to a 40mm bore yields 739 N each way. For this 450mm stroke, the long unsupported piston rod is susceptible to bending under side loads; always use an external guide to prevent rod-bearing damage.
This cylinder is dimensionally interchangeable per ISO 15552 and uses a reduced mounting accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB and CR brackets. Note that the adjustable air cushions only decelerate the piston near stroke end; they do not hold a load. If position holding without live air pressure is required, use a SAIL lock cylinder or an external pilot-operated check valve.
Quick checklist
Because it is a double-rod cylinder, the effective piston area is identical on both sides. It provides an equal force of 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa in both the extend and retract directions.
Yes, the SAID32X450-S is dimensionally interchangeable with other ISO 15552 profile cylinders. It shares the standard mounting footprint but uses a specific accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and requires PT port threading.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.