
The AirTAC SAID32 Double Rod Cylinder SAID32BX475 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 475mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X475 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 475mm stroke. Because the piston rod extends from both end covers, the annulus area is identical on both sides. This provides equal force and speed in both directions, yielding about 483 N of thrust and pull at 0.5 MPa.
This configuration uses a SUS304 stainless steel rod for superior corrosion resistance. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch placement. A rod exits the rear cover simultaneously with the front, allowing you to mount a secondary cam, position flag, or drive a second mechanism while maintaining dual-side guidance against rotation.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX475 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer carriage where the pushing and pulling loads are identical, ensuring consistent cycle timing without needing pressure adjustments.
Powers a vertical lifting slide where the twin rods prevent the platform from twisting under offset loads during the 475mm travel.
Uses the protruding rear rod end to trigger a mechanical limit valve or secondary mechanism independently of the primary front tooling.
Choose this 32mm bore when an application requires symmetric force (483 N each way at 0.5 MPa) and anti-rotation stability that a single-rod SAI cannot provide. If your project needs less force, stepping down is not an option in this series, but stepping up to a 40mm bore increases the bidirectional output to 739 N. For this 475mm stroke, the 12mm rod and M10x1.25 thread handle moderate side loads, but an external guide rail is recommended to prevent rod-bearing bending over the long travel distance.
This cylinder uses a PT tapered port thread and G1/8 air supply. It supports mounting accessories Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). Note that the adjustable air cushions only decelerate the piston near the stroke ends; they do not hold a load. If air pressure drops, the piston will drift, requiring an external pilot-operated check valve or a SAIL locking cylinder for position holding. It is dimensionally interchangeable per ISO 15552.
Quick checklist
Because it is a double-rod cylinder, the effective area is the same on both sides. It provides equal push and pull forces of 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa.
Yes, the SAID32X475 is dimensionally interchangeable with other ISO 15552 double-rod profile cylinders. It shares the standard mounting interface and uses a G1/8 port, though you should verify rear-rod clearance in your existing setup.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.