
The AirTAC SAID32 Double Rod Cylinder SAID32BX65S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 65mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X65-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 65mm stroke. Because the SUS304 stainless steel rod exits both end covers, the annulus area is identical on each side. This means you get exactly 345 N of output force in both extend and retract directions at 0.5 MPa, ensuring perfectly symmetric motion.
Equipped with a piston magnet (-S), this variant directly supports AirTAC CMSE reed and DMSE electronic solid-state sensors. The extruded aluminum barrel includes sensor grooves on both sides, while the PT tapered port threads match the standard G1/8 interface. You can mount a workpiece on the front rod end and a position flag or cam on the rear rod for dual-side guidance.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX65S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 65 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives a transfer mechanism where the 345 N force must remain identical in both directions, preventing jerky transitions on the return stroke.
Mounts a primary workpiece on the front rod and a secondary cam on the rear rod to trigger a limit switch at the exact end of the 65mm stroke.
Uses the twin SUS304 rods to guide a sliding component smoothly, resisting torsional twist without needing an external linear guide.
Select this 32mm bore when an application demands equal push and pull forces, which a single-rod SAI cannot provide. If you need slightly higher force, stepping up to the 40mm bore yields 528 N both ways at 0.5 MPa, but the 32mm is ideal for compact symmetric tasks. The twin-rod design inherently resists rotation better than a single rod, though external guidance is still recommended for heavy lateral loads.
This cylinder uses the reduced SAID mounting accessory set: Basic, FA, LB, TC, FTC, TCM1, and TCM2. It omits the FB, CA, CB, and CR mounts found on single-rod variants. Note that the adjustable air cushions at both ends only decelerate the piston near stroke end; they do not hold the load. If pressure is lost, the cylinder will drift, requiring a SAIL lock or external pilot-operated check valve for position holding.
Quick checklist
Because it is a double-rod cylinder, the effective piston area is identical on both sides. It provides 345 N of force in both the extend and retract directions at 0.5 MPa, and 621 N at 0.9 MPa.
Yes, the SAID32X65-S is dimensionally interchangeable per ISO 15552. It shares the same mounting footprint and G1/8 port interface, making it a direct replacement for other ISO 15552 double-rod cylinders.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.