
The AirTAC SAID32 Double Rod Cylinder SAID32BX90 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 90mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAID32X90 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 90mm stroke. Because the SUS304 stainless steel rod exits both end covers, the effective piston area is identical in each direction, yielding an equal extend and retract force of 483 N at 0.7 MPa. This symmetric output is ideal for mechanisms requiring consistent push and pull dynamics.
Beyond equal force, the twin-rod architecture provides superior anti-rotation stability compared to a single-rod SAI. You can mount the primary workpiece on the front rod end while using the rear protrusion to drive a cam or mount a physical limit flag. It uses adjustable air cushions at both ends to decelerate the piston smoothly.
| Model | Airtac SAID32 Double Rod Cylinder SAID32BX90 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Drives transfer arms where the 483 N push and pull forces must be perfectly matched, ensuring consistent cycle times in both directions without needing pressure adjustments.
Guides linear slides carrying delicate payloads, using the twin-rod geometry to resist torsional twist and maintain precise alignment without external guide rails.
Mounts the primary tool on the front rod while the rear SUS304 rod end drives a secondary cam or mechanical flag, synchronizing two separate machine actions in one stroke.
Select this 32mm bore when an application demands exactly 483 N of thrust and retraction force at 0.7 MPa. If your mechanism requires less force, stepping down is not an option in the SAID series as 32mm is the smallest bore; however, stepping up to a 40mm bore increases the both-way output to 739 N. Choose the double-rod SAID over a single-rod SAI when you need dual-side guidance, anti-rotation resistance, or a rear rod for secondary actuation.
This model features PT tapered port threads and a basic mounting setup. Note that SAID supports a reduced accessory set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. As a double-acting cylinder, it does not hold position automatically upon air loss; for locking requirements, consider the SAIL or BSAID series. The 90mm stroke is short enough to avoid rod-bearing bending, but always verify external side-load constraints.
Quick checklist
The SAID32X90 generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and 621 N at 0.9 MPa. Because it is a double-rod cylinder, these pull-side figures represent the exact force available in both the extend and retract directions.
Yes, the SAID32X90 is dimensionally interchangeable per ISO 15552. It serves as a direct replacement for other ISO 15552 double-rod profile cylinders, provided your setup accommodates the rear rod protrusion and uses PT G1/8 ports.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.