The AirTAC Airtac SC32 Standard Cylinder SC32X1055S is a genuine double-acting standard air cylinder with a Ø32mm bore and 1055mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC32X1055S is a double-acting tie-rod cylinder with a 32 mm bore and a non-standard stroke of 1055 mm, exceeding the standard maximum of 1000 mm for this bore size. It delivers 402 N of push force at 0.5 MPa and up to 724 N at the maximum operating pressure of 0.9 MPa, driven by a 12 mm diameter piston rod.
This model includes a built-in magnet (-S suffix), allowing direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors on the barrel for precise, non-contact position feedback. The cylinder operates on filtered air with standard PT ports and TPU seals, rated for a temperature range of -20 to +70 °C.
| Model | Airtac SC32 Standard Cylinder SC32X1055S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 1055 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×1055 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
The 1055 mm stroke is ideal for transferring light components between distant conveyor lines or workstations where a compact, tie-rod cylinder is needed.
Uses the full extended stroke to actuate a diverter gate in a sorting system, with the built-in magnet providing end-of-travel confirmation.
Applies 724 N of clamping force at 0.9 MPa on a fixture, with the -S magnet enabling sensors to verify the clamp is fully engaged before a cycle starts.
Select the SC32 bore for light pneumatic tasks requiring up to 402 N of force at 0.5 MPa. If your application demands higher force, consider stepping up to the SC40 bore, which provides 628 N at the same pressure. For this non-standard 1055 mm stroke, careful management of side loads is critical; an external guide or a self-guided cylinder is strongly recommended to prevent bending stress on the 12 mm rod.
When replacing this cylinder, match five key points: the 32 mm bore, the 1055 mm stroke, the PT port thread, the built-in magnet for sensor compatibility, and the basic mounting configuration. This is a non-ISO 15552 tie-rod cylinder and is dimensionally shorter, so it is only a direct drop-in replacement for another AirTAC SC32 tie-rod cylinder with the same specifications.
Quick checklist
At the standard 0.5 MPa operating pressure, the cylinder provides 402 N of push force and 345 N of pull force. At the maximum operating pressure of 0.9 MPa, the push force increases to 724 N.
No, 1055 mm is a non-standard stroke for the 32 mm bore, as the maximum standard stroke is 1000 mm. For such a long stroke, you must use an external guide or a guided cylinder to prevent the 12 mm rod from bending under side loads, as the cylinder's rod bearing alone is not designed to support them.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.