The AirTAC Airtac SC32 Standard Cylinder SC32X1100 is a genuine double-acting standard air cylinder with a Ø32mm bore and 1100mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC32X1100 is a double-acting tie-rod cylinder with a 32 mm bore and an extended 1100 mm stroke, built for applications needing a long reach from a compact body. This model delivers 402 N of push force at 0.5 MPa and 724 N at the maximum operating pressure of 0.9 MPa, driven by a 12 mm diameter piston rod.
With a body length A of 140 mm, the total extended length reaches 1240 mm. The adjustable pneumatic cushion (21 mm) decelerates the piston smoothly at both ends. This is a non-standard stroke exceeding the standard 1000 mm maximum, configured with PT1/8 ports, an M10x1.25 rod thread, and default TPU seals for -20 to +70 C operation.
| Model | Airtac SC32 Standard Cylinder SC32X1100 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 1100 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×1100 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
The 1100 mm stroke pushes lightweight components across wide conveyor gaps or indexing stations where a compact cylinder body is needed.
Operates a long-throw diverter gate in packaging lines, using the 12 mm rod to reach across the full lane width at moderate speed.
Drives a long-travel linear slide in test fixtures, where the 32 mm bore provides clean, oil-free pneumatic motion with adjustable end-cushioning.
Select the SC32 when your application requires a light, compact actuator with a push force up to 402 N at 0.5 MPa. If your load demands more force, step up to the SC40 bore, which provides 628 N at the same pressure. For this 1100 mm stroke, side-load management is critical; the slender 12 mm rod is susceptible to bending under lateral forces, so an external guide or linear rail is strongly recommended to protect the rod bearing and extend seal life.
To ensure a correct replacement, match these five points: 32 mm bore, 1100 mm stroke, PT1/8 port thread, your specific mounting accessory (this is a basic body, order brackets separately), and the magnet option (this model has no built-in magnet).
Quick checklist
At 0.7 MPa operating pressure, the theoretical push force is 563 N. The pull force on the retract stroke is lower due to the 12 mm rod area, delivering 345 N at 0.5 MPa.
It is not recommended. The 12 mm rod at a 1100 mm stroke is highly vulnerable to side-load bending and buckling. Always use an external guide rail or rod-alignment coupler to prevent premature rod bearing wear and seal failure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.