The AirTAC Airtac SC32 Standard Cylinder SC32X330S is a genuine double-acting standard air cylinder with a Ø32mm bore and 330mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC32X330S is a double-acting single-rod pneumatic cylinder with a 32 mm bore and 330 mm stroke, delivering 402 N of push force at 0.5 MPa (724 N at 0.9 MPa). Its 12 mm diameter piston rod and 21 mm adjustable air cushion provide reliable deceleration for moderate-speed automation tasks.
This model includes a built-in magnet (-S suffix), allowing direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors on the barrel for non-contact position sensing. The compact tie-rod design, with a body length of 140 mm, suits installations where space is limited and sensor feedback is required.
| Model | Airtac SC32 Standard Cylinder SC32X330S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 330 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×330 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Pushes lightweight components on a conveyor line, with sensors confirming extend and retract positions for precise sortation logic.
Applies consistent low-force clamping in electronics or plastics assembly, where the magnet allows end-of-stroke detection to prevent cycle errors.
Operates small fixtures or sampling mechanisms in lab automation, using the clean, oil-free air and sensor feedback for repeatable positioning.
Choose the SC32 bore for light-duty pushing, clamping, or sorting where force requirements stay below 402 N at 0.5 MPa. If your application demands higher force, step up to the SC40 bore (628 N at 0.5 MPa). For strokes of 300 mm or more, like this 330 mm unit, be mindful of side loads: an unsupported 12 mm rod can bend under lateral force. Use an external linear guide or a guided cylinder if the load is not perfectly axial. When replacing an existing cylinder, match five points: 32 mm bore, 330 mm stroke, PT port thread, basic mount (no bracket), and the built-in magnet (-S) for sensor compatibility.
Quick checklist
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At the maximum operating pressure of 0.9 MPa, push force reaches 724 N. The theoretical maximum at 1.0 MPa is 82 kgf.
Yes. The -S suffix indicates a built-in magnet specifically designed for AirTAC CMSG (reed) or DMSG/EMSG (solid-state) sensors. These sensors clamp directly onto the tie-rod barrel without additional brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.