Airtac SC32 Standard Cylinder SC32X430
The AirTAC SC32 Standard Cylinder SC32X430 is a genuine double-acting standard air cylinder with a Ø32mm bore and 430mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ32 mm
- Stroke430 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 21 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC32 Standard Cylinder SC32X430
The SC32X430 is a compact double-acting tie-rod cylinder delivering 402 N of push force at 0.5 MPa (724 N at 0.9 MPa). Its 12 mm diameter piston rod and 21 mm adjustable air cushion at both ends provide reliable deceleration for mid-stroke applications.
With a body length of 140 mm and a total extended length of approximately 570 mm, this 430 mm stroke model is well within the 1000 mm maximum standard stroke for the 32 mm bore. The PT1/8 port and M10x1.25 rod thread match common pneumatic fittings for straightforward integration.
Airtac SC32 Standard Cylinder SC32X430 Technical Specifications
| Model | Airtac SC32 Standard Cylinder SC32X430 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 430 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC32 Standard Cylinder SC32X430
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×430 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC32 Standard Cylinder SC32X430 Is Used
Small Part Ejection
Pushes lightweight components off a conveyor or out of a nest with its 430 mm reach, fitting into compact automation cells.
Lab Automation
Operates sample handling arms or dispenser actuators in clean, space-constrained laboratory instruments.
Diverter Gates
Actuates small diverter flaps on packaging lines, directing products between lanes with a 430 mm stroke.
Is the Airtac SC32 Standard Cylinder SC32X430 the Right Cylinder?
Choose the SC32X430 for light-duty pushing, clamping, or sorting where space is tight. If your load approaches the 402 N push force at 0.5 MPa, stepping up to the 40 mm bore provides 628 N at the same pressure. For strokes over 300 mm, ensure the 12 mm rod is not subjected to side loads; use an external guide or linear rail to prevent rod bending and premature bearing wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC32 Standard Cylinder SC32X430 FAQ
At the standard operating pressure of 0.5 MPa, the cylinder provides 402 N extending (push) and 345 N retracting (pull). At the maximum operating pressure of 0.9 MPa, the push force increases to 724 N.
This specific model code SC32X430 does not include the -S magnet option. To use CMSG/DMSG/EMSG reed or solid-state sensors, order SC32X430-S, which has a built-in magnet band on the piston.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC32 Standard Cylinder SC32X430
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.