The AirTAC Airtac SC32 Standard Cylinder SC32X575S is a genuine double-acting standard air cylinder with a Ø32mm bore and 575mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC32X575S is a double-acting tie-rod cylinder with a 32 mm bore and a non-standard 575 mm stroke, exceeding the standard 1000 mm maximum for this bore. It delivers 402 N of push force at 0.5 MPa and up to 724 N at the maximum operating pressure of 0.9 MPa, driven by a 12 mm diameter piston rod.
This model includes a built-in magnet (-S suffix), allowing direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors on the barrel for contactless position detection. The cylinder body length A is 140 mm, resulting in a total extended length of approximately 715 mm. It uses PT1/8 ports and an M10x1.25 rod thread, with an adjustable air cushion of 21 mm at each end to decelerate the piston smoothly.
| Model | Airtac SC32 Standard Cylinder SC32X575S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 575 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×575 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
The 575 mm stroke and sensor-ready magnet make this cylinder ideal for actuating stop gates on conveyor lines, where mid-stroke position confirmation is needed to control product flow.
With 724 N of force at 0.9 MPa, it provides consistent clamping in assembly jigs. The built-in magnet enables end-of-stroke sensing to verify the clamp is fully engaged before a cycle starts.
The extended 575 mm reach is well-suited for pushing finished parts off a shelf or out of a nest in automated storage and retrieval systems, where sensor feedback confirms a completed ejection.
For applications needing slightly more force, consider stepping up to the 40 mm bore, which provides 628 N at 0.5 MPa. The SC32X575S is a genuine AirTAC tie-rod cylinder, shorter than an ISO 15552 profile, so replacement must match bore, stroke, PT port thread, basic mounting, and the integrated magnet. At this 575 mm stroke, the 12 mm rod is susceptible to bending under side loads; use an external guide or a guided cylinder if the load is not purely axial.
Quick checklist
At the standard 0.5 MPa operating pressure, the push force is 402 N and the pull force is 345 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 724 N. The theoretical maximum force at 1.0 MPa is 82 kgf.
No. The AirTAC SC series is a tie-rod cylinder and is physically shorter than an ISO 15552 cylinder of the same bore and stroke, so it is not dimensionally interchangeable. It should only replace another AirTAC SC tie-rod cylinder with matching bore, stroke, PT ports, and magnet option.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.