The AirTAC Airtac SC32 Standard Cylinder SC32X600H is a genuine double-acting standard air cylinder with a Ø32mm bore and 600mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The SC32X600H is a double-acting pneumatic cylinder with a 32 mm bore and 600 mm stroke, delivering 402 N of push force at 0.5 MPa and up to 724 N at the maximum operating pressure of 0.9 MPa. This model is specified with high-temperature Viton (FKM) seals, extending the operating temperature range from the standard -20 to +70 °C up to 0 to +150 °C, making it suitable for autoclaves, drying ovens, and hot-process automation.
Its 12 mm diameter piston rod and PT1/8 ports are standard for the 32 mm bore SC family. The total extended body length is approximately 740 mm (140 mm body length A plus the 600 mm stroke). This is a genuine AirTAC tie-rod cylinder, designed for reliable double-acting service with filtered compressed air.
| Model | Airtac SC32 Standard Cylinder SC32X600H |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Viton seals allow the SC32X600H to operate reliably in the 0-150°C environment of steam autoclaves, controlling door locks or tray transfer mechanisms.
The 600 mm stroke provides the reach needed for traversing a hot melt adhesive head across a wide panel, with seals that resist the elevated process temperatures.
Raises and lowers a lightweight gate or diverter flap inside a continuous drying oven, where standard seals would quickly degrade from the sustained heat.
For applications requiring more force, stepping up to the SC40 bore provides 628 N at 0.5 MPa. This 600 mm stroke is within the 1000 mm maximum standard stroke for the 32 mm bore, but the slender 12 mm rod is susceptible to bending under side loads. For a 600 mm stroke, always guide the load externally with a linear rail or rod guide to prevent rod bearing damage and ensure long seal life. When replacing an existing cylinder, match the 32 mm bore, 600 mm stroke, PT1/8 port thread, and ensure the replacement uses Viton seals for high-temperature compatibility.
Quick checklist
At 0.7 MPa (7 bar), the theoretical push force is 563 N. The pull force on the retract stroke is slightly lower due to the rod area, providing 345 N at 0.5 MPa.
No. The SC32X600H is a double-acting cylinder and will not hold its position or a suspended load if air pressure is exhausted. The adjustable air cushion only decelerates the piston at the end of stroke. For load holding, you must add an external rod lock or a pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.