The AirTAC Airtac SC32 Standard Cylinder SC32X75N is a genuine double-acting standard air cylinder with a Ø32mm bore and 75mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC32X75N is a compact double-acting tie-rod cylinder delivering 402 N of push force at 0.5 MPa (563 N at 0.7 MPa). Its 32 mm bore and 75 mm stroke suit light pneumatic tasks where space and cycle speed matter, with a body length A of just 140 mm.
This model uses NBR (nitrile) seals, making it a reliable choice for general industrial air service within the standard -20 to +70 °C range. The 12 mm diameter piston rod and PT1/8 ports keep the unit lightweight, while the 21 mm adjustable air cushion at each end protects against hard end-of-stroke impacts.
| Model | Airtac SC32 Standard Cylinder SC32X75N |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
The 75 mm stroke and 402 N push force are ideal for ejecting lightweight components from conveyor lines or sorting gates in packaging machinery, operating reliably at speeds up to 800 mm/s.
Provides consistent, controlled clamping for small jigs and fixtures in electronics or medical device assembly, where the adjustable cushion prevents vibration that could misalign delicate parts.
Delivers the short, repeatable linear motion needed for label applicators, date stampers, or inkjet markers, with NBR seals offering good wear resistance in dry, clean-air environments.
Choose the SC32 bore when your application needs up to 402 N at 0.5 MPa; if you require more force, step up to the SC40 which provides 628 N at the same pressure. For strokes of 300 mm or longer, verify that side loads are minimal or add an external guide—the 12 mm rod can bend under high lateral stress.
To ensure a correct replacement, match five points: 32 mm bore, 75 mm stroke, PT1/8 port thread, NBR seal material, and the basic (no bracket) mounting configuration. This cylinder is not an ISO 15552 profile; it is a genuine AirTAC SC tie-rod design and will only directly interchange with another SC32 of identical specifications.
Quick checklist
At the standard operating pressure of 0.5 MPa, the cylinder produces 402 N of push force on extension and 345 N of pull force on retraction. At 0.7 MPa, push force increases to 563 N, and at the maximum operating pressure of 0.9 MPa it reaches 724 N.
No. The AirTAC SC series is a tie-rod cylinder that is physically shorter than an ISO 15552 profile cylinder, so the mounting dimensions are not interchangeable. You must replace it with another AirTAC SC32 tie-rod cylinder matching the 75 mm stroke, PT ports, and NBR seals.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.