Airtac SE100 Standard Air Cylinder SE100BX800SH
The AirTAC Airtac SE100 Standard Air Cylinder SE100BX800SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 800mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke800 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100BX800SH
The AirTAC SE100BX800SH is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty actuation and washdown environments. It generates 3927 N of push force and 3681 N of pull force at 0.5 MPa, utilizing a 100 mm bore and an 800 mm stroke. Equipped with a SUS304 stainless steel rod (code B) and a high-temperature FKM (Viton) seal (code H), it operates reliably from -20 to +150 C, resisting corrosion and thermal degradation in aggressive processing lines.
The extruded aluminum barrel eliminates external tie rods, yielding a compact, flush-mounting profile that naturally resists contamination. Field-adjustable pneumatic cushioning at both ends allows you to tune the end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speeds up to 800 mm/s. The integrated magnet (code S) directly supports AirTAC CMSE reed and DMSE electronic position sensing for precise stroke verification.
Airtac SE100 Standard Air Cylinder SE100BX800SH Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100BX800SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100BX800SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100BX800SH Is Used
Palletizer Film Wrap
Drives the film carriage on a heavy-duty pallet wrapping machine, using its 3927 N push force and 800 mm stroke to extend and retract smoothly in high-temperature packaging zones.
Chemical Reactor Lid
Lifts and seals a high-temperature chemical reactor vessel lid, leveraging the SUS304 rod and Viton seal to withstand corrosive vapors and 150 C ambient heat.
Die Casting Extraction
Extracts heavy automotive die-cast parts from a hot mold cavity, utilizing the 800 mm stroke and adjustable pneumatic cushions to safely decelerate the 3681 N pull load.
Is the Airtac SE100 Standard Air Cylinder SE100BX800SH the Right Cylinder?
Delivering 3927 N push at 0.5 MPa, this 100 mm bore is a heavy-duty workhorse. If your payload is lighter, stepping down to the 80 mm bore yields 2513 N push, while moving up to the 125 mm bore provides 6136 N for massive inertia. Remember that a standard SE cylinder relies on live air pressure to move; it cannot hold a load if air is lost or a valve is centered. For positive holding, consider the BSE rod lock variant.
At 800 mm of travel, the unsupported 25 mm rod is highly susceptible to bending under lateral deflection. An external linear guide is strongly recommended to prevent rod-bearing damage. For drop-in retrofits, match the 100 mm bore, 800 mm stroke, PT1/2 port, and your required ISO 15552 mounting hardware. The -S magnet enables CMSE or DMSE sensors for end-position confirmation.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100BX800SH FAQ
At 0.5 MPa, it provides 3927 N push and 3681 N pull. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf when operating at the maximum rated pressure of 1.0 MPa.
Yes. The SE series is dimensionally interchangeable per ISO 15552 standards. You can drop-in replace other ISO 15552 profile cylinders by matching the 100 mm bore, 800 mm stroke, PT1/2 port, and mounting interface, ensuring seamless retrofitting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100BX800SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.