Airtac SE100 Standard Air Cylinder SE100X1000S
The AirTAC Airtac SE100 Standard Air Cylinder SE100X1000S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 1000mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke1000 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100X1000S
The AirTAC SE100X1000S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. Operating at 0.5 MPa, it generates 3927 N of push force and 3681 N of pull force, scaling to a maximum of 801 kgf at 1.0 MPa. The 100 mm bore utilizes a PT1/2 port and a Ø25 mm hard-chrome rod with an M20x1.5 thread.
This unit features a square extruded aluminum barrel without external tie rods, creating a compact, corrosion-resistant body that mounts flush against machine frames. Equipped with a built-in magnet (-S), it supports AirTAC CMSE reed and DMSE electronic sensors along the three integrated sensor grooves. Field-adjustable air cushions at both ends allow precise deceleration tuning to absorb kinetic energy at stroke endpoints.
Airtac SE100 Standard Air Cylinder SE100X1000S Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100X1000S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100X1000S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100X1000S Is Used
Injection Mold Clamping
Provides 3927 N of push force at 0.5 MPa to secure injection mold halves during material injection, utilizing the 1000 mm stroke for large part ejection cycles.
Press Brake Backgauge
Positions heavy sheet metal backstops on CNC press brakes, where the 1000 mm stroke accommodates deep flange bending and the extruded profile resists shop floor debris.
Pallet Accumulation Stop
Acts as a high-force physical stop gate on heavy-duty roller conveyors, halting fully loaded pallets while the adjustable cushion softens the 801 kgf impact at stroke end.
Is the Airtac SE100 Standard Air Cylinder SE100X1000S the Right Cylinder?
Stepping down in bore size, the SE80 offers 2513 N of push at 0.5 MPa, whereas stepping up to the SE125 provides 6136 N, letting you fine-tune the actuator to the exact load. Because this unit has a 1000 mm stroke, the unsupported rod length increases bending moments on the front bearing; an external guide is strongly recommended to prevent premature wear and side-load damage. As a dimensionally interchangeable ISO 15552 profile cylinder, it serves as a direct drop-in replacement for other ISO 15552 cylinders, sharing standard mounting hardware. Remember that the adjustable air cushion only decelerates the piston near the stroke end; it does not hold the load if air pressure is lost, requiring a BSE rod lock for fail-safe positioning.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100X1000S FAQ
At 0.5 MPa, the SE100X1000S delivers 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N, with a maximum push of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE100X1000S is dimensionally interchangeable per ISO 15552 standards, serving as a drop-in replacement for other ISO 15552 cylinders using standard mounting accessories. However, it cannot hold a load without air pressure; the adjustable cushion only decelerates the piston near the end of the stroke, so a BSE rod lock is required for fail-safe holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100X1000S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.