Airtac SE100 Standard Air Cylinder SE100X270
The AirTAC Airtac SE100 Standard Air Cylinder SE100X270 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 270mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ100 mm
- Stroke270 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE100 Standard Air Cylinder SE100X270
The AirTAC SE100X270 is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 dimensional standard. It features a 100 mm bore and a 270 mm stroke, generating a substantial 3927 N of push force at 0.5 MPa and up to 5497 N at 0.7 MPa.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune deceleration via a set screw, softening hard end stops during high-speed cycles. This specific SKU lacks a built-in magnet, meaning it is not wired for CMSE or DMSE position sensing without modification.
Airtac SE100 Standard Air Cylinder SE100X270 Technical Specifications
| Model | Airtac SE100 Standard Air Cylinder SE100X270 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 270 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE100 Standard Air Cylinder SE100X270
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×270 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE100 Standard Air Cylinder SE100X270 Is Used
Injection Mold Clamping
Provides 3927 N of thrust at 0.5 MPa to secure mid-sized injection mold halves, utilizing the 270 mm stroke to accommodate varying mold depths.
Press Brake Tooling
Drives upper press brake tooling with 5497 N at 0.7 MPa, using the adjustable end cushions to soften the impact when reaching the bend depth.
Pallet Dispenser
Pushes empty pallets out of a vertical magazine, where the tie-rod-free extruded barrel allows flush side-mounting against the magazine frame.
Is the Airtac SE100 Standard Air Cylinder SE100X270 the Right Cylinder?
Stepping down to the 80 mm bore drops the 0.5 MPa push force to 2513 N, while moving up to the 125 mm bore raises it to 6136 N, letting you scale thrust precisely to the load. As a dimensionally interchangeable ISO 15552 unit, it serves as a direct drop-in replacement for other standard profile cylinders, reusing existing PT1/2 port plumbing and mounting hardware. Because the stroke is 270 mm, the 25 mm rod and its M20x1.5 thread will experience bending stress under lateral loads; always pair this unit with an external guide rail to prevent rod-bearing wear. Note that the air cushion only decelerates the piston near stroke end and does not hold a load if air pressure drops.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE100 Standard Air Cylinder SE100X270 FAQ
At 0.5 MPa, the SE100X270 delivers 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push increases to 5497 N, with a maximum push of 801 kgf at 1.0 MPa. It features a 25 mm rod with an M20x1.5 thread and a PT1/2 port.
Yes. The SE100X270 is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint, port spacing, and rod-end thread dimensions of other standard profile cylinders. You can reuse your existing FA or FB mounting brackets and PT1/2 pneumatic fittings during the retrofit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE100 Standard Air Cylinder SE100X270
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.