
The AirTAC SE80 Standard Cylinder SE80AX280 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 280mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE80AX280 is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It delivers a robust 2513 N push force at 0.5 MPa and utilizes a 25 mm SUS420J2 stainless steel rod, making it highly suitable for corrosive or washdown environments where standard carbon steel rods would degrade.
The extruded aluminum barrel features a clean, external tie-rod-free design that prevents debris accumulation and allows for flush mounting. Field-adjustable air cushions at both ends allow you to precisely tune end-of-stroke deceleration for fast 30-800 mm/s cycles, protecting machinery from hard impacts.
| Model | Airtac SE80 Standard Cylinder SE80AX280 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 280 mm stroke to route heavy PET bottle cases between processing lanes, leveraging the SUS420J2 rod for washdown durability against caustic cleaning agents.
Provides 2513 N of extend force at 0.5 MPa to pivot heavy bar-feed stock into the spindle, relying on adjustable cushions to absorb rapid 30-800 mm/s cycling impacts.
Drives a 80 mm bore platen to flatten corrugated cardboard sheets, where the tie-rod-free aluminum profile prevents paper dust accumulation inside the mechanism.
Delivering 2513 N push at 0.5 MPa, this 80 mm bore steps neatly between the 63 mm (1559 N) and 100 mm (3927 N) bores, letting you scale force up or down as your payload dictates. Because this SKU lacks a built-in magnet, position sensing requires external physical stops or a separate sensor bracket. Note that the adjustable cushion only decelerates the piston near stroke end; it cannot hold a load vertically if air pressure drops. For secure mid-stroke holding, consider the BSE rod-lock variant.
With a 280 mm stroke, the 25 mm rod carries substantial side-load capacity, yet long unsupported piston travel still risks rod-bearing bending. Implementing an external guide rail is strongly recommended to prevent premature seal wear. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 profile cylinders using existing PT3/8 ports and mounting hardware.
Quick checklist
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force reaches 3518 N. The absolute maximum push capacity is 513 kgf when operating at the maximum rated pressure of 1.0 MPa.
Yes. The SE80AX280 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting interface, PT3/8 port size, and 25 mm rod thread dimensions. You can drop it into existing hardware without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.