Airtac SE80 Standard Cylinder SE80AX5S
The AirTAC Airtac SE80 Standard Cylinder SE80AX5S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 5mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke5 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80AX5S
The AirTAC SE80AX5S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a robust 2513 N push force at 0.5 MPa. It features a SUS420J2 stainless steel rod (code A) specifically chosen for corrosive or washdown environments where standard carbon steel would fail. The square extruded aluminum barrel omits external tie rods, yielding a compact body that mounts flush against machine frames while resisting debris buildup.
Equipped with a built-in magnet (code S), this 80mm bore unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. Field-adjustable pneumatic cushioning at both ends allows technicians to tune the end-of-stroke deceleration via a set screw, softening hard impacts during rapid 30-800 mm/s cycling.
Airtac SE80 Standard Cylinder SE80AX5S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80AX5S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80AX5S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80AX5S Is Used
Stamping Press Ejection
Uses the 2513 N extend force to knock stamped metal parts out of tight dies, relying on the SUS420J2 rod to withstand residual cutting fluid spray.
Carton Flap Folding
Executes rapid 5mm tucks on high-speed packaging lines, utilizing the built-in magnet and DMSE sensors to confirm fold completion instantly.
Lab Washdown Clamping
Secures glass reactor vessels during CIP cleaning cycles, where the stainless steel rod prevents corrosion against harsh chemical washdowns.
Is the Airtac SE80 Standard Cylinder SE80AX5S the Right Cylinder?
Selecting this 80mm bore cylinder makes sense when your application requires substantial thrust; stepping down to the 63mm bore drops your 0.5 MPa push force to 1559 N, while stepping up to the 100mm bore increases it to 3927 N. The 5mm stroke provides ultra-short actuation, and the M20x1.5 rod thread handles high mechanical stress. Because the PT3/8 ports and standardized mounting interface match ISO 15552 footprints, you can directly swap this cylinder into existing setups using standard FA, LB, or TC mounting accessories.
Note that a plain SE cylinder cannot hold a load if air pressure drops or the valve is centered—the piston will drift. For gravity-loaded vertical setups requiring safety holding, consider the BSE rod-lock variant. Furthermore, while the adjustable air cushion decelerates the piston near stroke end, it functions only as a shock absorber and never as a braking mechanism.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80AX5S FAQ
The 80mm bore generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum of 513 kgf at 1.0 MPa. It operates at speeds ranging from 30-800 mm/s.
Yes, the SE80AX5S is dimensionally interchangeable with any standard ISO 15552 profile cylinder, meaning it shares identical mounting and port dimensions. You can swap it directly using your existing mounting hardware and PT3/8 pneumatic fittings.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80AX5S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.