Airtac SE80 Standard Cylinder SE80BX100H
The AirTAC Airtac SE80 Standard Cylinder SE80BX100H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 100mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke100 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80BX100H
The AirTAC SE80BX100H is a double-acting single-rod profile cylinder built to the ISO 15552 standard, generating 2513 N of push force and 2268 N of pull force at 0.5 MPa. This variant pairs a SUS304 stainless steel rod with a high-temperature FKM (Viton) seal, expanding the operating temperature range from -20 to +150 C for corrosive or washdown environments.
The extruded aluminum barrel design eliminates external tie rods, yielding a smooth, flush surface that resists debris buildup and simplifies clean-in-place procedures. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softly damping heavy 80 mm loads moving at speeds up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80BX100H Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80BX100H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80BX100H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80BX100H Is Used
Bakery Oven Doors
Handles high-heat actuation on commercial bakery oven doors, utilizing the FKM Viton seal rated to 150 C to withstand sustained thermal exposure.
CNC Machining Centers
Clamps heavy cast iron automotive blocks during CNC milling, relying on 2513 N of push force at 0.5 MPa to prevent vibration shift.
Pharmaceutical Washdown
Drives lifting mechanisms on pharmaceutical skids where the SUS304 stainless rod prevents corrosion during frequent chemical washdown cycles.
Is the Airtac SE80 Standard Cylinder SE80BX100H the Right Cylinder?
If you are sizing around this 80 mm bore, stepping down to the 63 mm bore yields 1559 N push at 0.5 MPa, while stepping up to the 100 mm bore provides 3927 N push at 0.5 MPa. Because this specific SKU lacks a built-in magnet, it cannot host CMSE or DMSE position sensors; add an -S suffix if electronic or reed switch feedback is required for your control system.
This model uses a PT3/8 port and an M20x1.5 rod thread. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct drop-in replacement for other standard profile cylinders, sharing identical mounting footprints and accessory hardware. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80BX100H FAQ
The SE80BX100H generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It features an 80 mm bore, a 25 mm rod, an M20x1.5 rod thread, and a PT3/8 port.
Yes. This model uses an FKM (Viton) seal rated for temperatures up to 150 C and a SUS304 stainless steel rod. The extruded ISO 15552 profile barrel lacks external tie rods, preventing fluid traps and making it highly suitable for washdown duty.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80BX100H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.