Airtac SE80 Standard Cylinder SE80BX600S
The AirTAC Airtac SE80 Standard Cylinder SE80BX600S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 600mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke600 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80BX600S
The AirTAC SE80BX600S is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding 600 mm stroke tasks. It generates 2513 N of push force at 0.5 MPa, utilizing a 25 mm rod with an M20x1.5 thread. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 dimensions for direct retrofitting.
This specific configuration features a SUS304 stainless steel rod (code B) for superior resistance in corrosive or washdown environments. Equipped with a built-in magnet (code S), it integrates seamlessly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard end stops during high-speed 30-800 mm/s cycling.
Airtac SE80 Standard Cylinder SE80BX600S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80BX600S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80BX600S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80BX600S Is Used
Bottling Line Diverters
Leveraging the 2513 N push force and 600 mm stroke, this cylinder drives large diverting arms on high-speed beverage bottling lines, while the SUS304 rod withstands daily caustic washdowns.
Automated Pallet Stops
Provides robust physical stopping power for heavy pallets on roller conveyors, utilizing the adjustable end cushions to absorb the kinetic energy of 800 mm/s transit speeds without slamming.
Corrugated Box Stackers
Actuates stacking flaps in packaging machinery, where the 600 mm stroke accommodates varying box heights and the built-in magnet triggers DMSE sensors to confirm stack completion.
Is the Airtac SE80 Standard Cylinder SE80BX600S the Right Cylinder?
If 2513 N push at 0.5 MPa is excessive for your load, the neighboring SE63 bore steps down to 1559 N push. For heavier demands, the SE100 bore steps up to 3927 N push. This 600 mm stroke approaches the 80 mm bore maximum standard of 1500 mm, meaning the 25 mm rod and M20x1.5 thread carry significant side-load risks over extended distances; an external guide rail is strongly recommended to prevent rod-bearing bending. Note that a plain SE cylinder does not hold its position if air pressure is lost or the valve centers—piston drift will occur. For load-holding safety, consider the BSE rod lock variant. As a dimensionally interchangeable ISO 15552 cylinder, it drops into existing mounts using the PT3/8 port and standard accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80BX600S FAQ
This 80 mm bore cylinder generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It features a PT3/8 air port and a 25 mm SUS304 rod.
Yes, the SE80BX600S is dimensionally interchangeable per ISO 15552 standards, meaning it shares identical mounting footprint and center distances. You can drop it into existing machinery using standard FA or LB mounts without redesigning the frame.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80BX600S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.