Airtac SE80 Standard Cylinder SE80BX800SCA
The AirTAC Airtac SE80 Standard Cylinder SE80BX800SCA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 800mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke800 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80BX800SCA
The AirTAC SE80BX800SCA is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It generates 2513 N of push force at 0.5 MPa and features an 800 mm stroke, making it well-suited for long-travel automation tasks. Built with a SUS304 stainless steel rod, this variant is explicitly designed for washdown environments and corrosive duty where a standard carbon steel piston would fail prematurely.
Unlike traditional tie-rod designs, its extruded aluminum profile barrel lacks external protruding rods, yielding a compact footprint that mounts flush against machine frames. The cylinder includes a built-in magnet for non-contact position sensing via CMSE reed or DMSE electronic switches, and the field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration to prevent hard mechanical impacts.
Airtac SE80 Standard Cylinder SE80BX800SCA Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80BX800SCA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80BX800SCA
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80BX800SCA Is Used
Bulk Package Sortation Diverter
Leverages the 800 mm stroke and 2513 N thrust to push heavy corrugated cartons off a high-speed main conveyor belt onto downstream packaging lanes.
Washdown Meat Processing Gate
The SUS304 stainless rod withstands daily high-pressure chemical washdowns, actuating a 80mm bore stainless hopper gate in poultry processing facilities.
Pallet Dispenser Pusher
Utilizes the CA clevis joint to accommodate angular misalignment while using the full 800 mm travel to index empty wooden pallets into an automated stretch wrapper.
Is the Airtac SE80 Standard Cylinder SE80BX800SCA the Right Cylinder?
When sizing this 80 mm bore actuator, evaluate your actual load requirements against its 2513 N push capacity at 0.5 MPa. If your application demands less force, stepping down to the 63 mm bore yields 1559 N of push, optimizing air consumption and physical envelope. Conversely, if you need to move heavier payloads, the 100 mm bore provides 3927 N of thrust. Remember that a standard double-acting cylinder does not hold its position if air pressure is lost or the valve is centered; the piston will drift. For fail-safe load holding, consider the BSE rod-lock variant or an external pilot-operated check valve.
At 800 mm of travel, the unsupported mass of the rod and piston creates a high bending moment on the front bearing. To prevent premature seal wear and rod-bearing failure under side loads, incorporate an external linear guide to support the load independently of the actuator. This model includes a CA single clevis mounting accessory for pivoting articulations and uses PT3/8 ports.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80BX800SCA FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N. The maximum theoretical push force is 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80BX800SCA is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders using existing mounting hardware and the standardized CA clevis footprint, though you must ensure your PT3/8 port connections match.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80BX800SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.