Airtac SE80 Standard Cylinder SE80X210S
The AirTAC Airtac SE80 Standard Cylinder SE80X210S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 210mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke210 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X210S
The AirTAC SE80X210S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics, delivering 2513 N of push force and 2268 N of pull force at 0.5 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 dimensions for seamless retrofitting.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-stop deceleration via a set screw, softening impacts during high-speed 30-800 mm/s cycles without relying on fixed rubber bumpers.
Airtac SE80 Standard Cylinder SE80X210S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X210S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 210 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X210S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×210 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X210S Is Used
Palletizer Flap Control
Driving 210 mm stroke flap mechanisms on palletizing lines where 2513 N of push force at 0.5 MPa securely folds heavy cardboard carton flaps prior to sealing.
Press Brake Demolding
Ejecting formed sheet metal parts from hydraulic press brakes, utilizing the 36 mm adjustable cushion to gently decelerate the 80 mm piston at high speeds.
Sorter Diverter Arm
Actuating heavy-duty diverter arms on package conveyor systems, where the built-in magnet triggers DMSE electronic sensors to confirm package routing.
Is the Airtac SE80 Standard Cylinder SE80X210S the Right Cylinder?
With an 80 mm bore generating 2513 N push at 0.5 MPa, this model sits between the 63 mm bore (1559 N push) and the 100 mm bore (3927 N push), allowing you to step down for lighter clamping or up for higher mass. Because the 210 mm stroke exceeds the 300 mm threshold, the 25 mm piston rod and M20x1.5 thread face increased bending moments under side loads; integrating an external guide rail is strongly recommended to prevent rod-bearing wear.
Note that the adjustable air cushion only decelerates the piston near stroke end and does not lock the load. If your fixture must hold vertical weight without live air pressure, step up to the BSE rod-lock variant or utilize an external pilot-operated check valve. For ISO 15552 drop-in replacements, match the 80 mm bore, 210 mm stroke, PT3/8 port, and -S magnet when sourcing mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X210S FAQ
At 0.5 MPa, the SE80X210S provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N. The absolute maximum push capacity is 513 kgf when operated at the maximum 1.0 MPa pressure.
Yes, the SE80X210S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it in to replace other ISO 15552 profile cylinders by matching the 80 mm bore, 210 mm stroke, PT3/8 port, and M20x1.5 rod thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X210S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.