Airtac SE80 Standard Cylinder SE80X30S
The AirTAC Airtac SE80 Standard Cylinder SE80X30S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 30mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke30 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X30S
The AirTAC SE80X30S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
Equipped with a built-in magnet, this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts even during rapid 30 mm strokes.
Airtac SE80 Standard Cylinder SE80X30S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X30S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X30S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X30S Is Used
Injection Mold Platen Ejector
Uses the 2513 N extend force to positively eject heavy molded plastic parts from a stationary platen within a rapid 30 mm stroke.
Heavy Carton Flap Folder
Drives a mechanical arm to fold thick corrugated cardboard flaps on a high-speed packaging line, relying on the 2268 N retract force to overcome spring resistance.
Hydraulic Press Stop Block
Acts as an adjustable mechanical stop in a hydraulic press setup, positioning the 25 mm rod rapidly to define the lower bending limit.
Is the Airtac SE80 Standard Cylinder SE80X30S the Right Cylinder?
This 80 mm bore generates 2513 N of push at 0.5 MPa. If your application requires less force, stepping down to the 63 mm bore yields 1559 N; conversely, scaling up to the 100 mm bore provides 3927 N. As a standard ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for comparable 80 mm bore, 30 mm stroke cylinders, utilizing standard PT3/8 ports and mounting hardware.
Because this is a short 30 mm stroke, rod-bearing bending is negligible and no external guide is required. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If the machinery must hold a vertical load without live air pressure, integrate an external BSE rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X30S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force reaches 3518 N. The maximum push force is 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X30S is dimensionally interchangeable per ISO 15552. You can drop it in as a replacement for other 80 mm profile cylinders, matching the standard PT3/8 port and mounting dimensions. The built-in magnet also allows seamless integration with AirTAC CMSE or DMSE position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.