verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE80 Standard Cylinder SE80X342S

The AirTAC SE80 Standard Cylinder SE80X342S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 342mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ80 mm
  • Stroke342 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM20×1.5
  • CushionAdjustable, 36 mm
$166.53 $174.03Save 4% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE80 stroke, mounting and version on one page All SE80 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE80 Standard Cylinder SE80X342S

The AirTAC SE80X342S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.

Equipped with a built-in position magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-cap deceleration, softening hard impacts during high-speed cycling.

Airtac SE80 Standard Cylinder SE80X342S Technical Specifications

ModelAirtac SE80 Standard Cylinder SE80X342S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ80 mm
Stroke342 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM20×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø80mm)

PressurePush forcePull force
0.5 MPa2513 N2268 N
0.7 MPa3519 N—
Max (@1.0 MPa)513 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE80 Standard Cylinder SE80X342S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
80Bore size in mm.
×342Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE80 Standard Cylinder SE80X342S Is Used

straighten

Pallet Dispenser Pusher

Uses the 2513 N extend force to separate and push heavy wooden pallets from a magazine stack into an automated packaging line.

conveyor_belt

Bottle Diverter Arm

Leverages the 342 mm stroke to reach across a wide conveyor, routing large beverage containers into a secondary labeling station.

factory

Press Ejector Mechanism

Employs the DMSE electronic sensor signal to confirm retraction before ejecting stamped metal parts from a hydraulic press bed.

Is the Airtac SE80 Standard Cylinder SE80X342S the Right Cylinder?

Choosing this 80 mm bore provides 2513 N push at 0.5 MPa. If your application requires less force, stepping down to the 63 mm bore yields 1559 N; stepping up to the 100 mm bore provides 3927 N. Because the 342 mm stroke creates a long lever arm on the 25 mm rod, an external guide is strongly recommended to prevent rod-bearing bending under lateral loads.

As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 80 mm bore, 342 mm stroke unit with a PT3/8 port. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load. If pressure is lost, the rod will drift, requiring a BSE rod lock for secure positioning.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE80 Standard Cylinder SE80X342S FAQ

The 80 mm bore generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. The air supply port size is PT3/8.

No, the adjustable air cushion only decelerates the piston near the end of the stroke and acts as a bumper, not a brake. If the pneumatic pressure is lost or exhausted, the piston will drift. To safely hold a vertical load, you must use a BSE rod lock cylinder or an external pilot-operated check valve.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE80 Standard Cylinder SE80X342S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE80X342S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.