Airtac SE80 Standard Cylinder SE80X430
The AirTAC Airtac SE80 Standard Cylinder SE80X430 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 430mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke430 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X430
The AirTAC SE80X430 is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard, delivering a robust 2513 N push force at 0.5 MPa and a maximum thrust of 513 kgf at 1.0 MPa. Its square extruded aluminum barrel completely eliminates external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames while leaving three integrated sensor grooves open for switches.
This 80 mm bore unit travels a 430 mm stroke and relies on field-adjustable pneumatic cushioning at both ends to decelerate the payload smoothly. Because this specific SKU lacks the -S magnet code, it is not equipped for AirTAC CMSE or DMSE position sensing out of the box. The cushioning is a true adjustable air cushion, not a fixed rubber bumper, allowing technicians to dial in end-of-stroke damping to match the moving load.
Airtac SE80 Standard Cylinder SE80X430 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X430 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 430 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X430
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×430 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X430 Is Used
Pallet Conveyor Diverter
Pushes heavy loaded pallets onto a secondary packaging line using its 2513 N thrust at 0.5 MPa, with the 430 mm stroke providing the full lateral travel needed to clear the main belt.
Injection Mold Ejection
Actuates a large mold ejection plate where the 80 mm bore delivers the necessary force to strip dense plastic parts, while the adjustable end cushions soften the high-speed retraction.
Metal Press Ejection
Kicks stamped metal blanks out of a hydraulic press bed, utilizing the 430 mm stroke to reach past the die cavity and the 513 kgf max thrust to overcome part adhesion.
Is the Airtac SE80 Standard Cylinder SE80X430 the Right Cylinder?
When sizing this 80 mm bore model, stepping down to the 63 mm bore drops the 0.5 MPa push output to 1559 N, while stepping up to the 100 mm bore increases it to 3927 N, giving you clear room to adjust if your payload requirements shift. Keep in mind that a standard SE cylinder does not hold its position or lock the load if air pressure is lost or the valve is centered; the piston will drift. For applications requiring true mid-air holding without live pressure, consider the BSE rod-lock variant or an external pilot-operated check valve. At 430 mm, this stroke is substantial, so the unsupported rod bearing faces bending moments under side loads—always use an external guide to prevent premature seal wear.
For a drop-in replacement, match the 80 mm bore, 430 mm stroke, PT3/8 port, and your required mounting accessory (such as FA front flange or TC center trunnion). Because it adheres to the ISO 15552 footprint, it is dimensionally interchangeable with other ISO 15552 profile cylinders, simplifying retrofits.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X430 FAQ
At 0.5 MPa, the SE80X430 delivers 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N. The maximum push force is 513 kgf when operating at the 1.0 MPa pressure limit.
Yes, the SE80X430 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards, meaning it shares the exact same mounting footprint and hardware interface as other ISO 15552 profile cylinders. Note that this specific SKU does not have a built-in magnet (-S), so it cannot be used with CMSE or DMSE sensors without modification.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X430
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.