verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE80 Standard Cylinder SE80X500

The AirTAC SE80 Standard Cylinder SE80X500 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 500mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ80 mm
  • Stroke500 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM20×1.5
  • CushionAdjustable, 36 mm
$189.59 $197.09Save 3% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE80 stroke, mounting and version on one page All SE80 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE80 Standard Cylinder SE80X500

The AirTAC SE80X500 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a robust 2513 N push force at 0.5 MPa and a maximum thrust of 513 kgf at 1.0 MPa. Its square extruded aluminum barrel omits external tie rods entirely, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.

This 80 mm bore unit traverses a 500 mm stroke at speeds of 30-800 mm/s, relying on a field-adjustable pneumatic cushion at both ends to decelerate the piston near stroke limits. Because this specific SKU lacks the -S magnet code, it cannot host CMSE or DMSE position sensors without modification, and the cushion merely softens end-stops rather than locking the load.

Airtac SE80 Standard Cylinder SE80X500 Technical Specifications

ModelAirtac SE80 Standard Cylinder SE80X500
SeriesSE ISO 15552 profile cylinder
Bore sizeØ80 mm
Stroke500 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM20×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø80mm)

PressurePush forcePull force
0.5 MPa2513 N2268 N
0.7 MPa3519 N—
Max (@1.0 MPa)513 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE80 Standard Cylinder SE80X500

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
80Bore size in mm.
×500Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE80 Standard Cylinder SE80X500 Is Used

straighten

Automotive Body Welding Clamp

Provides the 2513 N push at 0.5 MPa required to hold heavy steel body panels firmly against spot-welding fixtures during automated assembly.

conveyor_belt

Pallet Divert Arm

Uses the 500 mm stroke to extend a diverter arm across a wide packaging conveyor, redirecting heavy pallets onto secondary spur lines.

factory

Injection Mold Ejector

Drives a large mold ejection plate over 500 mm, leveraging the 36 mm adjustable cushion to soften the end-stop impact when stripping thick plastic parts.

Is the Airtac SE80 Standard Cylinder SE80X500 the Right Cylinder?

If 2513 N of push at 0.5 MPa overshoots your payload requirements, step down to the 63 mm bore, which yields 1559 N of thrust. Conversely, if your fixture demands heavier actuation, the 100 mm bore provides 3927 N at the same 0.5 MPa. When replacing an existing ISO 15552 actuator, match the 500 mm stroke, 80 mm bore, PT3/8 port, and your specific mounting accessory. Since this unit lacks a magnet, factor in external limit switches if position feedback is required. At 500 mm of stroke, the 25 mm rod and M20x1.5 thread endure significant bending moments under lateral loads; always pair this cylinder with an external guide rail to prevent rod-bearing wear.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE80 Standard Cylinder SE80X500 FAQ

At 0.5 MPa, the SE80X500 delivers 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force is 3518 N. The maximum push force is 513 kgf when operated at the 1.0 MPa pressure limit.

No, the SE80X500 is a standard double-acting cylinder and cannot hold a load without live pressure. The adjustable air cushion only decelerates the piston near stroke end; it does not act as a brake. For position holding, use an external rod lock or pilot-operated check valve.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE80 Standard Cylinder SE80X500

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE80X500 and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.