Airtac SE80 Standard Cylinder SE80X5S
The AirTAC Airtac SE80 Standard Cylinder SE80X5S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 5mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke5 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X5S
The AirTAC SE80X5S is a double-acting, single-rod ISO 15552 profile cylinder engineered for short-stroke actuation. It delivers a substantial 2513 N push force at 0.5 MPa and 3518 N at 0.7 MPa, making it highly effective for high-impact duties within a compact 5 mm travel. The extruded aluminum barrel omits external tie rods entirely, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames without snagging wiring or adjacent mechanics.
Equipped with a built-in magnet (indicated by the S code), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke confirmation. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, softening impacts even during rapid 30-800 mm/s cycling.
Airtac SE80 Standard Cylinder SE80X5S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X5S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X5S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X5S Is Used
Press Brake Tooling
Provides 2513 N of extend force at 0.5 MPa to rapidly seat and clamp sheet metal bending dies within a 5 mm travel window.
Stamping Pin Ejection
Cycles at up to 800 mm/s to eject small stamped metal parts from tight dies, using the integrated magnet to trigger DMSE sensors for part-confirm.
Cutoff Saw Stop
Acts as a high-force mechanical stop for automated cutoff saws, using the 3518 N push force at 0.7 MPa to resist cutting loads rigidly.
Is the Airtac SE80 Standard Cylinder SE80X5S the Right Cylinder?
When sizing this 80 mm bore actuator, compare its 2513 N push at 0.5 MPa against the neighboring bores: step down to the 63 mm cylinder for 1559 N if your load is lighter, or step up to the 100 mm bore for 3927 N if you need greater thrust. Because the 5 mm stroke is extremely short, side-load bending on the 25 mm rod and rod bearing is minimal, though you should still ensure rigid mounting to avoid misalignment.
For retrofits, the SE80X5S is dimensionally interchangeable per ISO 15552, meaning it drops directly into existing footprints using standard FA, LB, or TC mounting hardware. Remember that a standard SE cylinder does not hold its load when air is exhausted or the valve is centered; if your process requires fail-safe position holding, integrate an external pilot-operated check valve or specify the BSE rod-lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X5S FAQ
The SE80X5S generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It features a PT3/8 port and a 25 mm rod.
Yes, the SE80X5S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing ISO 15552 mounting hardware, but you must ensure your pneumatic plumbing matches the PT3/8 port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X5S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.