Airtac SE80 Standard Cylinder SE80X620SCBCR
The AirTAC Airtac SE80 Standard Cylinder SE80X620SCBCR is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 620mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke620 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X620SCBCR
The AirTAC SE80X620SCBCR is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a robust 2513 N push force at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The integrated -S magnet enables seamless position detection using AirTAC CMSE reed or DMSE electronic sensors.
Equipped with a CB double clevis mounting interface, this unit accommodates pivoting articulations while enduring high kinetic energy. Field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration via a set screw, softening hard mechanical impacts during rapid 30-800 mm/s cycling.
Airtac SE80 Standard Cylinder SE80X620SCBCR Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X620SCBCR |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 620 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X620SCBCR
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×620 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X620SCBCR Is Used
Palletizer Push-Off Arm
Leverages the 2513 N thrust at 0.5 MPa to reliably sweep finished pallets off a heavy-duty roller conveyor during high-speed packaging operations.
Injection Mold Ejector
Uses the 620 mm stroke to fully extract deep-cavity automotive interior panels from molding presses, relying on the CB clevis to absorb angular off-center loads.
Hydraulic Press Material Feeder
Pushes heavy steel blanks into a forming press, utilizing the field-adjustable cushioning to prevent shock damage when stopping 80 mm bore inertia at 800 mm/s.
Is the Airtac SE80 Standard Cylinder SE80X620SCBCR the Right Cylinder?
Selecting this 80 mm bore yields 2513 N of thrust at 0.5 MPa. If your payload is lighter, stepping down to the 63 mm bore drops output to 1559 N, whereas upgrading to the 100 mm bore increases thrust to 3927 N for heavier loads. The CB clevis mount pairs with the CR joint to handle angular misalignment during articulation.
Because this unit features a 620 mm stroke, the extended rod is susceptible to bending under lateral loads; an external guide rail is strongly recommended to prevent rod-bearing wear. Note that while the adjustable air cushion decelerates the piston near stroke end, it does not lock the load—if air pressure is lost or the valve is centered, the piston will drift, requiring a BSE rod lock for secure holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X620SCBCR FAQ
This 80 mm bore cylinder provides 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. Its operating speed ranges from 30-800 mm/s.
Yes, the SE80X620SCBCR is dimensionally interchangeable per ISO 15552, allowing it to serve as a drop-in replacement for other ISO 15552 profile cylinders using the same CB mounting footprint and PT3/8 port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X620SCBCR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.